BODY SHOP GUIDE – Hudson Valley MRO Reference

Bolts 

Hex head machine screw thread fasteners with cone points serve multiple applications in automotive assembly, including attachment of hood hinges to hoods and fenders, mounting of radiator supports, installation of radiator grilles, and various general-purpose fastening requirements commonly encountered in body shop and collision repair work around Kingston, New York.

Flanged locking system fasteners incorporate serrated teeth that engage the mating surface to provide enhanced joint strength and improved assembly reliability, requiring approximately 30 percent greater torque for removal compared to non-locking designs. 

These fasteners maintain their locking characteristics through multiple disassembly and reassembly cycles, typically withstanding up to fifteen repeated installations. 

The dog point feature on these fasteners facilitates accurate alignment of body panels during assembly. The integral flange design eliminates the need for separate washers, reducing component count and assembly time.

USS coarse thread body bolts provide fastening solutions where coarse thread engagement is specified for the application.

SAE fine thread body bolts offer fastening capability in applications requiring fine thread specifications.

Hex flange head body bolts feature a black phosphate surface finish that provides corrosion resistance and reduces friction during installation.

Hex head body bolts supplied with loose washers incorporate a black phosphate finish for corrosion protection.

Hex flange head body bolts with starter points combine the washer-eliminating flange design with tapered pilot points that guide initial thread engagement.

Hex head body bolts featuring loose washers and starter points provide the alignment benefits of pilot points along with separate washer components, all finished with black phosphate coating.

Hex head body bolts with dog points and integral washers incorporate alignment pins for precise panel positioning during assembly.

Hex head body bolts supplied with loose washers and dog points combine separate washer components with panel alignment capabilities.

Universal bumper fasteners with round heads are manufactured from stainless steel and feature open-end designs with USS-specification head dimensions.

Torx washer head body bolts with starter points are designed for GM vehicle applications and general automotive use, featuring zinc surface finishes for corrosion resistance.

License plate fasteners consist of slotted washer head bolts supplied with corresponding nuts for universal vehicle license plate mounting applications.

____________________________________________________________________________

Clips 

Moulding clips are manufactured with a top head measuring 12.5 mm, a middle head measuring 15 mm, and a bottom head measuring 15 mm, with a stem diameter of 10.2 mm, specifications commonly used in exterior trim and moulding retention for body shop repairs in and around Fishkill, New York.

T-bolt clips are supplied with a 10-24 x 3/4 bolt and a 5/16 x 1-25/32 plate.

T-bolt clips are supplied with a 10-24 x 3/4 bolt and a 1/2 x 1-7/16 plate.

Weatherstrip clips feature a top head measuring 5mm x 15mm, a bottom head measuring 9.5mm, a stem diameter of 7mm, and a stem length of 11mm.

Weatherstrip clips are manufactured with a bottom head measuring 6.5mm, a stem diameter of 8.5mm, and a stem length of 7mm. These clips are constructed from white nylon.

Weatherstrip clips feature a top head measuring 5mm x 15mm, a bottom head measuring 6.5mm, a stem diameter of 7mm, and a stem length of 7mm.

Weatherstrip clips are manufactured with a bottom head measuring 5mm x 15mm, a top head measuring 8mm, and a stem diameter of 8mm. These clips are constructed from white nylon.

Weatherstrip clips feature a top head measuring 4mm, a bottom diameter of 6.5mm, a stem diameter of 6mm, and a stem length of 10mm. These clips are constructed from black nylon.

Weatherstrip clips are manufactured with a head diameter of 6.5mm x 14mm, a stem diameter of 6mm, and a stem length of 13mm. These clips are constructed from white nylon.

Weatherstrip clips feature a head diameter of 5mm, a bottom diameter of 7mm, a stem diameter of 7mm, and a stem length of 8mm. These clips are constructed from white nylon.

Weatherstrip clips are manufactured with a head measuring 9mm, a stem diameter of 6.5mm, and a stem length of 13mm. These clips are constructed from black nylon.

Weatherstrip clips feature a bottom head measuring 5mm, a stem diameter of 6.5mm, and a stem length of 6mm.

Weatherstrip clips are manufactured with a head size of 14mm, a stem diameter of 9mm, and a stem length of 11mm.

Grille clips have an overall height of 14mm (9/16). These clips are constructed from white nylon.

Grille clips feature a top head measuring 10mm x 10mm, a stem diameter of 10mm, and a stem length of 15mm.

Grille clips have an overall length of 24mm and a width of 14mm for radiator grille applications. These clips are constructed from gray nylon.

Grille clips have an overall height of 27mm. These clips are constructed from gray nylon.

Grille clips are manufactured with a top head measuring 15.5mm x 11mm, a bottom head measuring 19.5mm x 14mm, and a stem length of 11mm.

Door panel trim clips fit an 8mm hole.

Door panel trim clips feature a pan head diameter of 1/2 inch and fit a 1/4 inch hole.

Door panel retaining clips are designed for interior trim applications. Door and window crank handle retaining clips are manufactured in zinc and yellow finishes. 

Door trim panel clips include an anti-rattle wedge constructed from phosphate material. 

Door trim panel clips for rear hood cowl weatherstrip applications feature a bottom head measuring 8mm by 18mm, a top head of 12mm, and a stem diameter of 5mm, constructed from black nylon. 

Door trim panel clips for front and rear door applications have a bottom head measuring 5mm by 15mm, a top head of 6mm, and a stem diameter of 8mm, manufactured in blue nylon.

Door trim panel clips with a stem length of 14mm fit 7mm holes and are constructed from yellow nylon. 

Hood insulation retaining clips feature a bottom head of 7mm, a top head of 12mm, and a stem diameter of 7mm in black nylon. 

Fender apron seal clips have a bottom head of 17mm, a top head of 8mm, and a stem diameter of 7mm, constructed from black nylon.

Rocker panel moulding clips feature a stem length of 1-1/4 inches, a bottom head measuring 7/16 inch by 1-9/16 inches, and a top head measuring 11/16 inch by 1-1/2 inches. 

Rocker panel moulding clips designed to fit 8mm by 14mm holes have a 10mm stem and are manufactured in gray nylon, corresponding to OE number 25649693. 

Rocker moulding clips measuring 7/8 inch by 2 inches are specified for Pontiac Bonneville applications and are constructed from black nylon, corresponding to OE numbers 25691949 and 25704001. 

Rocker panel moulding clips with a stem length of 9/16 inch fit 1/8 inch holes and feature a bottom head measuring 13/16 inch by 13/16 inch and a top head of 13/16 inch, corresponding to OE number 11518357.

Wire loom routing clips fit 6.3mm holes and accommodate loom inner diameters of 10mm and outer diameters of 13mm, corresponding to OE number 12160858. 

Body side moulding clips have a stem length of 12mm and a head diameter measuring 6.5mm by 13mm, constructed from white nylon and corresponding to OE number 75305-S0A-003. 

Cotton top retaining clips feature a bottom head of 14mm, a top head of 9mm, and a stem diameter of 15mm in black nylon, corresponding to OE number 91501-SM4-003.

Engine splash shield clips measuring 13/16 inch by 1-7/16 inches are designed for front bumper cover to air dam applications and are manufactured with zinc organic coating, corresponding to OE number W701295-S301. 

Rocker panel moulding clips feature a top head measuring 9/16 inch by 25/32 inch, a bottom head measuring 3/8 inch by 25/32 inch, and a stem length of 9/16 inch, corresponding to OE number 25742293. 

Rocker panel moulding clips with a top head measuring 15/32 inch by 13/16 inch, a bottom head measuring 15/32 inch by 25/32 inch, and a stem length of 9/16 inch correspond to OE number 757B-16241-AA.

Wheel lip moulding clips have a stem diameter of 15mm, fit 10mm holes, and are constructed from yellow nylon. Fender moulding clips feature a stem length of 5mm and a head diameter of 12mm in white nylon. 

Cable clips have an overall height of 7mm when closed, accommodate a maximum cable diameter of 5mm, and are constructed from black nylon, corresponding to OE number 91558-SE3-003.

Fuel line retainer clips feature a head size of 3/8 inch by 5/8 inch, an overall height of 11mm, and are designed for 5/16 inch fuel hose applications in white nylon, corresponding to OE number 41729-A317-AA. 

Belt moulding clips have an overall length of 23mm and are constructed from pink nylon, corresponding to OE number 91503-T2A-A01. 

Fender moulding clips feature a stem length of 11mm and a head diameter of 7mm in red nylon, corresponding to OE number 90904-67037.

Bumper strip retainers fit 7mm by 7mm holes, accommodate 4mm screw sizes, and measure 10mm in width and 11mm in length, corresponding to OE number 90468-04030. 

Front fender and bumper cover clips have a head diameter of 18mm and a stem length of 25mm, constructed from black nylon and corresponding to OE number 47749-58010. 

Front fender and bumper cover clips measuring 25mm in width and 34mm in length are constructed from black nylon and correspond to OE number 53879-58010, with use specified alongside the part bearing number 724201.

Bumper cover clips measure 35mm in width and 25mm in overall length, constructed from black nylon and corresponding to OE number 53879-50020. 

Fender panel moulding clips feature a head size of 4.5mm by 11mm and a stem length of 9mm in black nylon, corresponding to OE number 90467-07137. 

C clips measure 20mm in width and 30mm in overall length, designed for fender panel applications and corresponding to OE number 63048-9Y000.

Flange clips have an overall length of 12.5mm with a 10.5mm hex configuration, designed for wheel liner cowl applications and corresponding to OE number 01553-05131. 

Hood seal clips feature a bottom head measuring 6.4mm by 16mm, a top head measuring 8.3mm by 6mm, and a stem diameter of 10mm in black nylon, corresponding to OE number 65810-K2000. 

Moulding and trim fasteners have an overall length of 22mm with 9mm spacing, constructed from black spring steel and corresponding to OE numbers A40-867-276 and 001-991-76-70.

Rocker panel moulding clips feature a bottom head of 17mm, a top head measuring 11mm by 14mm, a stem diameter of 9.7mm, and a stem length of 12mm in black nylon, corresponding to OE number 90913-0109. 

Spring locking clips with locking stem fit 6.5mm applications and are designed for front and rear spoiler mounting, manufactured with dacromet coating and corresponding to OE number 76879-44010.

Wheel flare moulding clips feature a top head measuring 14mm by 29mm, a bottom head measuring 14mm by 29mm, fit 9mm holes, and have a stem length of 16mm in white nylon. 

Wheel flare moulding clips with a top head measuring 14mm by 18mm, a bottom head measuring 14mm by 21mm, fitting 9mm holes with a stem length of 16mm are constructed from white nylon.

Drip moulding clips with sealer have a top width of 25mm, an overall length of 18mm, fit 5mm holes, and feature a stem length of 14mm in white nylon. 

Rocker moulding clips with sealer fit 9mm holes and feature a top head measuring 12mm by 20mm, a bottom head measuring 12mm by 24mm, and a stem length of 14mm in white nylon, corresponding to OE number 11610495.

Rocker moulding clips fit 9mm holes and feature a top head measuring 12mm by 20mm, a bottom head measuring 14mm by 20mm, and a stem length of 14mm in yellow nylon, corresponding to OE numbers 11546635 and 11612122. 

Rocker moulding clips fitting 9mm holes with a top head measuring 9.5mm by 20mm, a bottom head measuring 14mm by 20mm, and a stem length of 20mm are constructed from yellow nylon, corresponding to OE numbers 11568921 and 15864780.

Hood prop rod clips fit small square holes and accommodate rods with an 8mm diameter, constructed from nylon. 

Hood prop rod clips accommodate 8mm diameter rods and are manufactured from nylon. Hood prop rod clips for 8mm rod sizes have an overall length of 33mm and are constructed from black nylon. 

Hood prop rod clips fit 7mm square holes, have a head size of 15mm, and accommodate 8mm rod sizes in black nylon. 

Hood prop rod clips designed to fit 7mm square holes with a head size of 15mm accommodate 8mm rod sizes and are constructed from black nylon.

Windshield panel clips for lower side applications are manufactured in white nylon. Rear window clips are constructed from white nylon. 

Upper and lower windshield clips are manufactured in white nylon. Windshield, skylight, rear, and quarter window clips are constructed from white nylon. 

Rear window clips are manufactured in white nylon. Windshield and backlite clips are constructed from white nylon.

Moulding clips fit 10mm holes and feature a head size measuring 14mm by 16mm with a stem length of 12mm in white nylon. 

Moulding clips feature a top head measuring 5mm by 11mm, a bottom head of 8mm, a stem diameter of 6mm, and a stem length of 7mm. 

Moulding clips with a stem length of 18mm and stem dimensions of 8mm by 6mm include a blue rubber boot and are constructed from white nylon.

Moulding clips feature a stem length of 11mm with stem dimensions of 8mm by 6mm, include a blue rubber boot, and are constructed from white nylon. 

Moulding clips with a stem length of 11mm and stem dimensions of 8mm by 6mm are manufactured in white nylon. 

Moulding clips featuring a stem length of 11mm with stem dimensions of 8mm by 6mm are constructed from white nylon.

Moulding clips have an overall height of 29mm with stem dimensions of 8mm by 6mm, specified for driver side applications and constructed from white nylon. 

Moulding clips feature a head diameter of 12mm and a stem length of 11mm in white nylon. 

Moulding clips with a head size of 10mm by 20mm and a stem length of 14mm are constructed from black nylon.

Moulding clips feature a head size of 10mm by 38mm and a stem length of 12mm in white nylon. 

Moulding clips with a head size of 12mm by 21mm and a stem length of 11mm are constructed from white nylon. 

Moulding clips fit 10mm holes and feature a head diameter of 14mm by 38mm, a bottom head diameter of 16mm by 38mm, and a stem length of 14mm.

Moulding clips have a bottom head diameter of 8mm and a stem length of 12mm in white nylon. 

Moulding clips feature a head size of 11mm by 21mm and a stem length of 11mm in white nylon. 

Moulding clips fit 10mm holes and feature a head diameter of 14mm by 38mm, a bottom head diameter of 16mm by 38mm, and a stem length of 14mm. 

Bent moulding clips measure 8mm in width by 37mm in length and are constructed from white nylon.

Moulding clips feature an overall height of 27mm with dimensions of 25mm W x 36mm L and are constructed from white nylon material.

Moulding clips fit 9mm holes and feature a top head diameter of 14mm x 34mm, a bottom head diameter of 14mm x 33mm, and a stem length of 14mm.

Moulding clips fit 9mm holes and feature a head size of 20mm x 40mm, a stem length of 14mm, and an overall height of 30mm.

Moulding clips with sealer feature a top head of 13mm x 13.5mm, a bottom head of 12mm x 14mm, and a stem length of 9mm. These windshield moulding clips are designed for specific applications.

Moulding clips with sealer fit 9mm holes and feature a top head of 14mm x 18mm, a bottom head of 18mm x 21mm, and a stem length of 15mm.

Moulding clips with sealer fit 9mm holes and feature a top head of 14mm x 18mm, a bottom head of 14mm x 18mm, and a stem length of 15mm.

Moulding clips with sealer fit 9mm holes and feature a top head of 12mm x 20mm, a bottom head of 15mm x 20mm, and a stem length of 15mm. These clips are used for rocker panel applications.

Moulding clips with sealer feature a top head of 12mm x 20mm, a bottom head of 12mm x 24mm, and a stem length of 16mm. These clips are used for bumper applications.

Moulding clips with sealer fit 9mm holes and feature a top head of 15mm x 15mm, a bottom head of 20mm x 20mm, and a stem length of 15mm.

Moulding clips fit 9mm holes and feature a top head of 16mm x 23mm, a bottom head of 17mm, and a stem length of 12mm.

Moulding clips feature a head size of 11mm x 20mm, an overall height of 13.5mm, and a stem diameter of 11mm. These clips are constructed from white nylon material.

Moulding clips feature a top head of 12mm x 14mm and a stem length of 13mm. These clips are used for rocker panel applications.

Moulding clips fit 8mm holes and feature a top head of 11mm x 15mm, a bottom head of 16mm, and a stem length of 9.5mm.

Moulding clips fit 9mm holes and feature a top head of 12mm x 16mm, a bottom head of 12mm x 20mm, and a stem length of 24mm.

Moulding clips fit 9mm holes and feature a top head of 12mm x 29mm, a bottom head of 12mm x 20mm, and a stem length of 20mm.

Moulding clips fit 9mm holes and feature a top head of 12mm x 20mm, a bottom head of 12mm x 20mm, and a stem length of 11mm.

Moulding clips fit 9mm holes and feature a top head of 12mm x 16mm, a bottom head of 12mm x 20mm, and a stem length of 24mm.

Moulding clips fit 10mm holes and feature a head size of 22mm x 46mm and a stem length of 17mm. These clips are used for rocker applications.

Moulding clips fit 7/16 holes and feature a top head of 15.52 x 25.32, a bottom head of 12 x 25.32, and a stem size of 4.2. These clips are used for windshield garnish and trim applications.

Moulding clips feature a head size of 13.5mm x 20.5mm, an overall length of 22mm, and a screw size of M4.2. These clips are used for windshield garnish and trim applications.

Moulding clips with metal reinforcement feature a top head of 17mm x 20mm, a bottom head of 14mm x 28mm, and a stem length of 11mm. These clips are used for windshield pillar interior applications.

Moulding clips with metal reinforcement feature a top head of 17mm x 20mm, a bottom head of 14mm x 28mm, and a stem length of 12mm. These clips are used for windshield pillar interior applications.

Moulding clips with sealer fit 8mm holes and feature a top head of 8mm x 15mm, a bottom head of 15mm, and a stem length of 13mm.

Moulding clips with sealer fit 10mm holes and feature a top head of 22mm x 45mm, a bottom head of 25mm x 37mm, and a stem length of 15mm.

Moulding clips fit 7mm holes and feature a top head of 6.5mm x 15mm, a bottom head of 13mm x 26mm, and a stem length of 8mm.

Moulding clips fit 8mm holes and feature a top head of 12mm x 20mm, a bottom head of 12mm x 20mm, and a stem length of 15mm.

Moulding clips with sealer fit 8mm holes and feature a top head of 12mm x 20mm, a bottom head of 12mm x 24mm, and a stem length of 16mm. These clips are constructed from gray nylon material.

Moulding clips fit 8mm holes and feature a top head of 12.5mm x 23mm, a bottom head of 16mm, and a stem length of 11mm.

Moulding clips fit 8mm holes and feature a top head of 12.5mm x 23mm, a bottom head of 18mm, and a stem length of 11mm.

Moulding clips fit 8mm holes and feature a top head of 12mm x 20mm, a bottom head of 12mm x 20mm, and a stem length of 15mm.

Moulding clips feature a top head of 7.5mm x 10mm, a bottom head of 9.5mm, and an overall height of 16mm. These clips are constructed from white nylon material.

Moulding clips feature a head size of 13mm x 15mm and a stem length of 15mm. These clips are constructed from white nylon and are used for fender trim applications.

Moulding clips are constructed from tan and green nylon materials and correspond to OE number 91519-SCV-A01.

Moulding clips feature a top head of 18mm x 15mm, a bottom head of 11.6mm x 16mm, and an overall height of 14.8mm. These clips are constructed from white nylon and correspond to OE number 72431-S2K-003.

Moulding clips feature an overall height of 14mm and an overall length of 13mm. These clips are constructed from white nylon and correspond to OE number 75305-SHJ-003.

Moulding clips with adhesive feature an overall length of 82mm and a width of 8mm. These clips are constructed from blue nylon and are used for windshield moulding applications. These clips correspond to OE number 91570-SZA-305.

Moulding clips with sealer feature a top head of 11mm x 13mm, a bottom head of 15.5mm x 19mm, and a stem length of 19mm. These clips correspond to OE number 91503-SJ3-003.

Moulding clips with sealer feature a top head of 13mm x 17mm, a bottom head of 15mm x 22mm, and a stem length of 19mm. These clips are constructed from white nylon and correspond to OE number 71591-S5A-000.

Moulding clips feature a head size of 19mm, a stem length of 25mm, and an overall length of 40mm. These clips are constructed from yellow nylon and correspond to OE number 91578-T0A-003.

Moulding clips with sealer feature a top head of 12mm x 16mm, a bottom head of 16mm, a stem diameter of 9.5mm, and a stem length of 10mm. These clips correspond to OE number 87703-H1000.

Moulding clips with sealer feature a top head of 10mm x 12mm, a bottom head of 14mm x 20mm, a stem diameter of 4mm, and a stem length of 10mm. These clips correspond to OE number 87756-1F000.

Moulding clips with sealer feature a top head of 10mm x 12mm, a bottom head of 13mm x 15mm, and a stem length of 13mm. These clips are used for front hood applications and correspond to OE number 86360-3L000.

Moulding clips with sealer feature a top head of 16mm and a stem diameter of 5mm. These clips are used for rocker moulding applications and correspond to OE number 87756-37000.

Moulding clips with sealer feature a top head of 10mm x 12mm, a bottom head of 13mm x 15mm, and a stem length of 13mm. These clips are used for front hood applications and correspond to OE number 87758-39000.

Moulding clips with sealer feature a top head of 12mm x 15mm, a bottom head of 14mm x 36mm, a stem diameter of 4mm, and a stem length of 10mm. These clips correspond to OE number 87770-27000.

Moulding clips with sealer feature a top head of 10mm x 12mm, a bottom head of 14mm x 18mm, and a stem length of 10mm. These clips are constructed from white nylon and correspond to OE number 87758-35010.

Moulding clips with sealer feature a top head of 11mm x 15.5mm, a bottom head of 16mm, and a stem length of 12mm. These clips are used for rocker moulding applications and correspond to OE number 87702-H1000.

Moulding clips with sealer feature a top head of 16mm x 18mm, a bottom head of 18mm x 20mm, and a stem length of 18mm. These clips are constructed from blue nylon and correspond to OE number 87758-3L000.

Moulding clips feature a head size of 9mm and a stem length of 15mm. These clips are constructed from white nylon.

Moulding clips feature a top head of 13mm x 13mm, a stem length of 19mm, and a tan length of 10mm. These clips correspond to OE number 26398-ED000.

Moulding clips feature a head size of 8mm x 22mm and a stem length of 16mm. These clips are constructed from black nylon and correspond to OE number 87756-2G000.

Moulding clips feature a top head of 10mm x 15mm, a bottom head of 16mm x 18mm, and a stem length of 9mm. These clips are constructed from white nylon and correspond to OE number 86359-93500.

Moulding clips with sealer feature a top head of 10.5mm x 9.5mm, a bottom head of 41mm x 17.5mm, a stem diameter of 14mm, and a stem length of 10mm. These clips correspond to OE numbers 87759-3E000 and 87758-3E000.

Moulding clips with sealer feature a top head of 11mm x 13mm, a bottom head of 12mm x 20mm, and a stem length of 10mm. These clips are constructed from red nylon and correspond to OE number 87756-35000.

Moulding clips feature a head size of 10mm x 20mm, a stem length of 24mm, and an overall length of 26mm. These clips are used for front and rear spoiler applications and correspond to OE number 75392-35220.

Moulding clips feature a head size of 18mm and an overall length of 24.5mm. These clips are constructed from black nylon and correspond to OE number 75393-60030.

Moulding clips feature an overall length of 55mm and a width of 15mm. These clips are constructed from blue nylon and correspond to OE number 75545-53011.

Moulding clips with sealer feature a top head of 11mm x 13mm, a bottom head of 25mm x 25mm, and a stem length of 14mm. These clips are constructed from red nylon and correspond to OE number 90467-12072.

Moulding clips with sealer feature a screw size of M5.5, which is equivalent to number 12, a head size of 22mm, and an overall length of 24mm. These clips are used for front bumper applications and correspond to OE number 52197-30040.

Moulding clips feature a top head of 10mm x 23mm, a bottom head of 18mm, and a stem length of 18mm. These clips are constructed from white nylon and correspond to OE number 90467-12074.

Moulding clips feature a top head of 12mm, a bottom head of 18mm x 26mm, and a stem length of 10mm. These clips are constructed from white nylon and correspond to OE number 90467-12071.

Moulding clips feature a top head of 10mm x 15mm, a bottom head of 17mm, a stem diameter of 5mm, and a stem length of 9mm. These clips correspond to OE number E11451W24.

Moulding clips feature an oval size of 18mm x 16mm and an overall length of 21.5mm. These clips are constructed from white nylon and correspond to OE number 001-988-49-81.

Moulding clips feature an overall length of 45mm, an overall height of 16mm, and dimensions of 11mm W x 45mm L. These clips correspond to OE number 006-988-89-78.

Moulding clips feature an overall length of 20mm and a width of 19mm. These clips are constructed from white nylon and correspond to OE number 124-988-04-78.

Moulding clips feature a width of 22.5mm and an overall length of 23mm. These clips are constructed from white nylon and correspond to OE number 001-988-50-81.

Moulding clips feature an oval size of 12mm x 16mm, a stem length of 7mm, and an overall height of 16mm. These clips are used for front fender applications and correspond to OE number 001-988-44-81.

Moulding clips feature a stem length of 6mm, an overall length of 32.5mm, and a width of 23mm. These clips are constructed from white nylon and correspond to OE number 001-988-90-81.

Moulding clips feature an overall length of 25mm, an overall height of 21.5mm, and a width of 18.5mm. These clips are used for front and rear door applications and correspond to OE number 001-988-46-81.

Moulding clips feature an overall length of 48mm and a width of 32.5mm. These clips are used for front and rear door applications and correspond to OE number 007-988-71-78.

Moulding clips feature an oval size of 12.5mm x 15.5mm, a stem length of 7mm, and an overall height of 15.5mm. These clips are used for front fender applications and correspond to OE number 001-988-60-81.

Moulding clips feature an overall length of 32mm, an overall height of 25.5mm, and a width of 19mm. These clips are used for quarter panel applications and correspond to OE number 001-988-63-81.

Moulding clips fit from hole and feature a top head of 11.5mm x 19mm, a bottom head of 21mm, and a stem length of 11mm. These clips correspond to OE number 713-7707-315.

Moulding clips feature a top head of 11mm x 19mm, a bottom head of 21mm, and a stem length of 11mm. These clips are constructed from gray nylon and correspond to OE number 07-13-275-821.

Moulding clips feature a top head of 16mm x 20mm, a middle head of 18mm, a bottom head of 23mm, and a stem length of 19mm. These clips correspond to OE number 07-13-440-419.

Moulding clips feature a top head of 16mm x 20mm, a middle head of 18mm, a bottom head of 23mm, and a stem length of 21mm. These clips correspond to OE number 51-71-172-742.

Moulding clips fit from hole and feature a top head of 10mm x 15mm, a bottom head of 18mm, and a stem length of 12mm. These clips correspond to OE number 76882-CG1A.

Moulding clips feature a bottom head of 15mm, a stem diameter of 3.5mm, and a stem length of 7mm. These clips correspond to OE number 79998-4N000.

Moulding clips feature a top head of 14mm x 14mm, a bottom head of 16mm, and a stem length of 10mm. These rocker moulding clips correspond to OE number 76882-DF000.

Moulding clips fit 5.5mm holes and feature a top head of 12mm x 15mm, a bottom head of 16mm, and a stem length of 13mm. These clips correspond to OE number 01523-00911.

Moulding clips feature an overall height of 25mm, which is equivalent to 1 inch, a bottom head of 14mm x 22.5mm, and a stem length of 13mm. These clips correspond to OE number 90249-FC401.

Moulding clips feature a top head of 11mm x 14mm, a bottom head of 14mm x 17mm, and a stem length of 10mm. These clips are used for upper front bumper applications and correspond to OE number 57700-FC010.

Moulding clips with sealer fit 9mm holes and feature a top head of 11mm x 14mm, a bottom head of 14mm x 17mm, and a stem length of 12mm. These clips correspond to OE number 91503-PC030.

Moulding clips with sealer feature a top head of 11mm x 14mm, a bottom head of 17mm, and a stem length of 10mm. These clips correspond to OE number 90139-0008.

Moulding clips with sealer feature a head size of 21.5mm x 24mm, a stem diameter of 14.5mm, and a stem length of 17mm. These clips are constructed from white nylon and correspond to OE number 91505-FC110.

Moulding clips feature a top head of 8mm x 8mm, a bottom head of 15mm, and a stem length of 7mm. These clips correspond to OE number 75819-33010.

Moulding clips feature a head size of 43mm x 54mm and an overall height of 26mm. These clips are constructed from black nylon and are used for rocker panel applications. These clips correspond to OE number 76924-47010.

Moulding clips feature an overall height of 12.4mm, which is equivalent to 1/2 inch. These clips are constructed from white nylon and are used for door and garnish applications. These clips correspond to OE number 67771-58010.

Moulding clips feature a top head of 5mm x 10mm, a bottom head of 18mm, and a stem length of 13mm. These clips correspond to OE number 75395-0T010.

Moulding clips fit 9mm square holes and feature a head size of 17mm and a stem length of 8.5mm. These clips are used for hood and front fender applications and correspond to OE number 90467-11099.

Moulding clips feature a top head of 12mm x 13mm, a stem length of 22mm, and an overall length of 25mm. These clips are constructed from white nylon and correspond to OE number 52535-06030.

Clips feature a top head of 13mm x 31mm and an overall height of 30mm. These clips are constructed from black nylon and are used for front fender, sheet metal, and upper seal applications. These clips correspond to OE number 61991-35010.

Clips feature a top head of 13mm x 31mm and an overall height of 34mm. These clips are constructed from black nylon and are used for front fender, sheet metal, and upper seal applications. These clips correspond to OE number 61992-35010.

Moulding clips feature an overall height of 12mm. These clips are constructed from pink nylon and are used for door, rear deck, roof garnish, and instrument panel applications. These clips correspond to OE number 90467-12080.

Moulding clips with sealer feature a top head of 13mm, a bottom head of 20mm, and a stem length of 10mm. These clips are used for rear light housing guide applications and correspond to OE number 81496-21010.

Moulding clips feature an overall height of 14mm. These clips are constructed from white nylon and are used for rear hatch door side garnish and front body pillar garnish applications. These clips correspond to OE number 90467-09204.

Moulding clips fit 10mm x 10mm openings and feature a head size of 23mm x 28mm and a stem length of 14mm. These clips are used for rocker applications and correspond to OE number 90467-12073.

Moulding clips feature a head size of 22mm and an overall length of 24mm. These clips are used for rear door, hatch garnish, and luggage compartment applications. These clips correspond to OE number 76817-12060.

Moulding clips with sealer fit 8mm holes and feature a head size of 18mm and a stem length of 13mm. These clips are constructed from white nylon and correspond to OE number 75867-AC020.

Moulding clips fit 10mm x 10mm holes and feature a top head of 11mm x 13mm, a bottom head of 14mm x 25mm, and a stem length of 15mm. These clips correspond to OE number 90467-12075.

Moulding clips fit 8mm holes and feature a top head of 16mm, a middle head of 17mm, and a bottom head of 17mm. These clips correspond to OE number 30624192.

Moulding clips fit 8mm holes and feature a top head of 15mm x 17mm, a bottom head of 19mm x 16mm, and a stem length of 11mm. These clips correspond to OE number 30784514.

Moulding clips feature a top head of 11mm x 15mm, a bottom head of 11mm, a stem diameter of 4mm, and a stem length of 11mm. These clips correspond to OE number 191-853-577-A.

Moulding clips feature a stem length of 16mm, an overall length of 38.5mm, and a width of 34mm. These clips are used for door applications and include a blue rubber grommet. These clips correspond to OE number 1H0-853-585.

Moulding clips feature a stem length of 16mm, an overall length of 38.5mm, and a width of 34mm. These clips are used for door applications and include a blue rubber grommet. These clips correspond to OE number 1H0-853-585-B.

Moulding clips feature a stem length of 16mm, an overall length of 40mm, and a width of 23mm. These clips are used for quarter panel applications and include a white rubber grommet. These clips correspond to OE number 1H0-853-585-A.

Moulding clips feature a width of 8mm and an overall length of 31mm. These clips are constructed from white nylon and correspond to OE number 191-853-733-A.

Moulding clips feature a width of 24.5mm, a stem length of 12mm, and an overall length of 27mm. These clips include a white rubber grommet and correspond to OE number 3B0-853-576.

Moulding clips feature a width of 16mm, a stem length of 13mm, and an overall length of 17mm. These clips include a white rubber grommet and correspond to OE number 3A0-853-575-A.

Clips feature a width of 17.5mm, a stem length of 12mm, and an overall length of 21mm. These clips include a white rubber grommet and correspond to OE number 380-853-575.

Moulding clips feature a width of 20mm and an overall length of 41.5mm. These clips are constructed from nautical nylon and are used for front door fender and quarter panel applications. These clips correspond to OE number 4A0-853-909-A.

Moulding clips feature a width of 22mm, an overall length of 35mm, and an overall depth of 8mm. These clips are constructed from white nylon and are used for front headlamp clips and front and rear door applications. These clips correspond to OE number 4A0-853-825-A.

Moulding clips feature an overall length of 35mm and fit 22mm holes. These clips are constructed from white nylon and are used for front and rear door applications. These clips correspond to OE number 4A0-853-825-B.

Moulding clips feature a head size of 12mm x 15mm, a stem diameter of 10mm, and a stem length of 5mm. These clips are used for door and trim stuff plate applications and correspond to OE number 191-853-577.

Moulding clips fit 10mm holes and feature a width of 10mm and a stem length of 28.5mm. These clips are used for rocker panel applications and correspond to OE number 3A0-853-909.

Moulding clips feature a width of 35mm, a stem length of 14mm, and an overall length of 38mm. These clips are used for door fender and quarter panel applications and include a blue rubber boot. These clips correspond to OE number 3A0-853-575.

Moulding clips feature a width of 26mm, a stem length of 6mm, and an overall length of 34.5mm. These clips are constructed from white nylon and are used for rear door applications. These clips correspond to OE number 4A0-853-825-C.

Moulding clips feature a width of 25mm, an overall length of 40mm, and a thickness of 3mm. These clips are constructed from white nylon and correspond to OE number 6C0-868-246-A.

Moulding clips fit 8mm holes and feature a top head of 13mm x 16mm, a bottom head of 14mm, and a stem length of 13mm. These clips correspond to OE number 3C0-853-585.

Trim panel clips correspond to OE number 8-178894.

Push rod clip locking components feature a rod diameter of 5/32 and are designed for right side applications. These clips are constructed from red nylon and correspond to OE numbers 3454220 and 4658676.

Door lock rod locking push rod clips feature a rod diameter of 5/32 and are designed for left side applications. These clips are constructed from green nylon and correspond to OE numbers 3454221 and 4658677.

Door lock rod clips correspond to OE numbers 12.2337688, 14051674, and 4243830.

Door lock rod clips are designed for right hand applications. These clips are constructed from white nylon and correspond to OE number YJ3Z-1521970-AA.

Door lock rod clips feature a rod diameter of 5/32. These clips are constructed from gray nylon and correspond to OE numbers 16629990 and 16675980.

Door lock rod clip is manufactured from natural nylon and is designed for an 8 mm hole. The clip has an overall height of 20 mm and fits a 5 mm rod.

Door lock rod end clip fits a 5 x 32 rod diameter and uses a 2-piece fold-over design. The clip is made of white nylon.

Door lock rod end clip fits a 5 x 32 rod diameter. The clip is made of yellow nylon.

Door lock rod end clip fits a 5 x 32 rod diameter. The clip is made of black nylon.

Door lock rod end clip fits a 5 x 32 rod diameter and includes a 15/64 inch hole size. The clip is for the right side and is manufactured from natural nylon.

Door lock rod end clip is configured for the right side.

Door lock rod end clip fits a 0.196 rod diameter and is specified for a 0.140 panel thickness.

Door lock rod retaining clip fits a 0.38 rod diameter and is for the right side.

Moulding grommet has a head size of 18 mm x 25 mm and a stem length of 16 mm. The grommet is specified for screw size M4.2 (No.8) and is manufactured from yellow nylon.

Moulding retainer with sealer is specified for screw size M3.5 (No.6). The retainer has a head size of 13 mm x 13 mm, a stem diameter of 12 mm, and a stem length of 10 mm.

Moulding nut has a 16 mm flange and an overall height of 11 mm. The nut size is 6 mm, and the stem height is 10 mm.

Trim panel clip has a 19 mm head and an overall length of 34 mm. The clip supports a panel range of 1.75-5 mm, fits a 7 mm hole, and is manufactured from natural nylon.

Retaining clip is sized 6.3 mm x 9 mm and has a 14 mm head. The clip is used on various front end fascia applications.

Retaining clip fits an 8 mm hole and is used for weatherstrip retention.

Retaining clip has a head size of 21 mm, a stem diameter of 9.5 mm, and a stem length of 16 mm. The clip is manufactured from black nylon.

Windshield moulding clip has a head size of 14.5 mm x 30 mm and a bottom leg width of 26 mm. The clip is manufactured from white nylon.

Windshield clip has a width of 16 mm and an overall length of 55 mm. The clip is manufactured from blue nylon.

Windshield garnish clip has a 12 mm head size, an overall length of 44 mm, and a stem length of 24 mm.

____________________________________________________________________________

Door Hinges 

Door hinge bushings have an inside diameter of 5/16, an outside diameter of 13/32, and a height of 3/8. OE coverage includes D9AZ-6522841A and 972197.

Door hinge bushings have an inside diameter of 1/2, an outside diameter of 13/16, and a height of 3/8. OE coverage includes 20429500.

Door hinge bushings have an inside diameter of 5/16, an outside diameter of 11/32, and a height of 3/8. OE coverage includes D9AZ-6522841A.

Door hinge pin and bushing kits repair one hinge.

Door hinge pin and bushing kits repair one hinge and use greasable stainless steel, with OE coverage including 19260056, and are commonly applied in routine door alignment and hinge service work performed by body shops in and around Mahopac, New York.

Door hinge pin and bushing kits repair one hinge.

Door hinge pin and bushing kits repair one hinge and use greasable stainless steel.

Door hinge pin and bushing kits repair one hinge and use greasable stainless steel.

Door hinge pins have a length of 4-5/32, a diameter of 11/32, and a head outside diameter of 15/32, and they are zinc plate coated. OE coverage includes 12338015 and 14066728.

Door hinge pins have a length of 5-1/4, a diameter of 11/32, a shoulder outside diameter of 3/8, and a head outside diameter of 9/16. OE coverage includes 15591860, 15691595, 15967691, and 8881731.

Door hinge pins have a length of 4-1/8, a diameter of 11/32, a shoulder outside diameter of 3/8, and a head outside diameter of 1/2. OE coverage includes 15653790.

Door hinge pins have a length of 3-3/8, a diameter of 11/32, and a head diameter of 9/16, and they are zinc plate coated. OE coverage includes D9ZZ-6643030-AA.

GM truck door hinge pin and bushing repair kits are specified for OE coverage 89025539.

Door hinge repair kits use forged pins with bronze.

Door hinge roller kits repair one hinge and use greasable stainless steel. OE coverage includes 19260063.

GM door hinge springs may require a spring compressor for installation.

Slide door lower hinge bushings have an inside diameter of .25/64, an outside diameter of .375/32, and a height of .23/64. Spline coverage includes .05/256209, 15964972, and 16632192.

Slide door upper hinge bushings have an inside diameter of 11/32, an outside diameter of .43/64, and a height of .20. OE coverage includes 12338074, 15691493, 15964971, and 16632193.

Hinge pin and bushing kits repair 2 slide cargo doors and use greasable stainless steel. OE coverage includes 19260663.

Hinge pin and bushing kits repair 2 hinges and use stainless steel.

Hinge pin and bushing kits repair 2 hinges and use stainless steel and are greasable.

Hinge pin and bushing kits repair 2 hinges.

Hinge pin and nut kits are used for tailgate repair, repair 2 hinges, and use greasable stainless steel.

Hinge pin and nut kits are used for door hinge repair, repair 2 hinges, and use greasable stainless steel.

Hinge pin bushing and bracket kits repair 1 hinge, use greasable stainless steel, and include a bracket. OE coverage includes 19260660.

Hinge pin bushing and bracket kits repair 1 hinge, use greasable stainless steel, and include a bracket. OE coverage includes 19260058.

____________________________________________________________________________

Grommets

Retainer fits 11mm retainers with a head size of 16mm, a stem length of 16mm, and an overall length of 20mm.

Grommet retainer has a top head size of 12.5mm x 15mm and a bottom head size of 15mm x 17mm, with a stem length of 14mm and an overall length of 18mm.

Grommet retainer has a head size of 15mm x 17mm, a stem length of 13mm, and an overall length of 15mm.

Cowl screw grommet fits cowl screw grommets with a 10mm x 15mm hole and a blue 4.8mm (No. 10) screw specification.

Bumper grommet uses a 4.8mm (No. 10) screw and is made of black nylon.

Fender lining screw grommet fits a 9mm square hole with a stem length of 15mm and a head diameter of 18mm, and it uses a 5.5mm screw.

Fender lining screw grommets fit an 8 mm × 8 mm hole with a stem length of 22 mm and a head diameter of 22 mm, using a 5.5 mm screw, and are routinely used in inner fender and splash shield installations performed by body shops in Yonkers, New York.

Fender lining screw grommet has a stem length of 18mm and a head diameter of 16mm, and it uses a 5.5mm screw and is made of black nylon.

Moulding grommet is specified for a flange hole with an overall length of 21.5mm and a panel range of 1.5mm.

Interior trim grommet has a head size of 17mm x 19mm and a stem length of 9mm, and it is made of red nylon.

Door panel grommet fits a 9mm hole with a head size of 19mm and a stem length of 12mm, and it is made of green nylon.

Grommet fits a 9mm hole with a head size of 15mm and a stem length of 21mm, and it has an overall length of 25mm.

Bumper grommet fits a 17mm x 20mm hole with a head size of 27mm x 30mm and a stem length of 22mm, and it is specified as a rear bumper grommet with seal.

Tail lamp grommet has a head size of 13mm x 17mm and a stem length of 10mm, and it is made of black nylon.

Door glass to regulator grommet has a head size of 13.5mm and an overall length of 14mm.

Grommet has a diameter of 25mm and a stem diameter of 22mm, and it is made of black nylon.

Bumper screw grommet is specified with a 5mm (No.12) screw size and an overall length of 22mm, and it is made of natural nylon.

Bumper grommet is specified with a 6mm (No.10) screw size, a head size of 20mm, a stem length of 22mm, and an overall length of 42mm.

Grille grommet fits an 11mm hole with a head size of 20mm and a stem length of 18mm, and the application is grille.

Moulding screw grommet with sealer fits an 8mm hole with a 4.2mm (No. 8) screw size, a head size of 14mm, and a stem length of 18mm.

Moulding screw grommet with sealer fits an 8mm hole with a 5.5mm (No.12) screw size, a head size of 15.4mm x 19mm, and a stem length of 15mm, and it is made of yellow nylon.

Moulding grommet has an overall width of 20mm and is made of black nylon.

Cowl and dash grommet fits an 8mm hole with a head size of 14mm and a stem length of 7mm, and the application is cowl and dash grommet.

Moulding grommet has a flange of 13mm, an overall length of 12mm, and an ID of 7mm, and it is made of blue rubber.

Screw grommet with sealer fits a 4mm square hole with a head diameter of 13mm and a 5mm screw specification, and it is made of natural nylon.

Moulding grommet with sealer has a stem length of 13mm and a head size of 13mm x 13mm with a panel range of 1mm, and it has an overall length of 14mm.

Spoiler grommet with sealer has a head diameter of 12mm x 16mm and a stem diameter of 14mm, and the application is black glass lower and quarter glass moulding, and it is made of black nylon.

Tall light grommet has a head size of 24mm x 9mm and a stem length of 22mm, and it has an overall height of 24.5mm.

Grommet with sealer fits a 7mm hole with a head size of 12mm x 14.5mm and a stem length of 15mm.

Moulding grommets with sealer have a flange of 24mm and a stem length of 12mm. Moulding grommets with sealer are made of white nylon, have a head size of 14mm x 18mm, and have a stem length of 13mm.

Grommets with sealer fit an 8mm hole, have a head size of 17.5mm, and have a stem length of 15mm. Grommets with sealer are specified for cowl top, quarter glass, and exterior applications.

Rubber grommets have an ID of 3/8, an OD of 1/2, a groove width of 1/16, and a groove dia of 5/16. 

Rubber grommets have an ID of 1/4, an OD of 1/2, a groove width of 1/16, and a groove dia of 3/8. 

Rubber grommets have an ID of 5/8, an OD of 9/16, a groove width of 1/16, and a groove dia of 7/16. 

Rubber grommets have an ID of 3/8, an OD of 7/8, a groove width of 1/16, and a groove dia of 5/8. 

Rubber grommets have an ID of 1/2, an OD of 7/8, a groove width of 1/8, and a groove dia of 3/4. 

Rubber grommets have an ID of 5/8, an OD of 1, a groove width of 1/8, and a groove dia of 7/8.

Screw grommets fit a 10mm x 8mm hole and have a head size of 4.8mm. 

Screw grommets fit an 8.5mm square hole, measure 13mm W x 13mm L, use a 5mm screw size, and are made of natural nylon. 

Screw grommets fit an 8mm square hole, measure 12mm W x 12mm L, use a 5mm screw size, and are made of natural nylon. 

Screw grommets fit an 8mm x 8.5mm hole, measure 17mm W x 17mm L, use a 5mm screw size, and are made of natural nylon. 

Screw grommets fit a 7mm x 7mm hole, measure 13mm W x 13mm L, use a 4mm screw size, and are made of natural nylon. 

Screw grommets fit an 8.5mm square hole, measure 13mm W x 13mm L, use a 5mm screw size, and are made of natural nylon. 

Screw grommets fit an 8mm square hole, measure 9.5mm W x 9.5mm L, use a No. 6 screw size, and are made of natural nylon. 

Screw grommets measure 14mm W x 14mm L, use a 5mm screw size, are specified for headlight adjusting screws, and are made of white nylon. 

Screw grommets fit a 7mm x 7mm hole, have a head dia of 13mm, use a 4mm screw size, and are made of natural nylon. 

Screw grommets fit an 8.5mm square hole, have a stem of 21mm, have a head dia of 18mm, and use a screw size of 6.3mm-1.81mm. 

Screw grommets fit an 8.5mm square hole, have a stem of 17mm, have a head dia of 20mm, and use a screw size of 6.3mm-1.81mm. 

Screw grommets fit an 8mm square hole, have a stem of 18mm, have a head size of 18mm, have a stem size of 16mm, and are made of white nylon. 

Screw grommets fit an 8mm square hole, have a stem of 10mm, have a head dia of 13.5mm, and use a 4mm screw size. 

Screw grommets fit a 7mm square hole, have a stem of 9.5mm W x 9.5mm L, use a 4mm screw, and have a stem of 16mm. 

Screw grommets fit a 7mm square hole, have a stem of 10mm, have a head dia of 14mm, and use a 4mm screw size. 

Screw grommets fit an 8mm square hole, have a stem of 17mm, have a head dia of 19mm, and use a 5mm screw size. 

Screw grommets fit an 8mm square hole, have a stem of 7mm, have a head dia of 16mm, and use a 4mm screw.

Screw grommets with sealer fit a 7mm square hole, have a stem of 12mm, measure 15mm W x 15mm L, and use a 5mm screw size.

Screw grommets fit an 8.5mm square hole and have a 17mm stem, an 18mm head diameter, and a 5mm screw. OEM manufacturer references are 01281-00023, 90189-06001, and MD-098145.

Screw grommets fit a 7mm square hole and measure 10mm W x 10mm L, with a 15mm stem and a 3mm screw. OEM manufacturer reference is 90189-04007.

Screw grommets fit a 7mm square hole and measure 9.5mm W x 9.5mm L, with a 4mm screw and a 17mm stem, and they are made of white nylon. OEM manufacturer reference is 34301-692A-000.

Screw grommets fit a 7mm square hole and measure 9.5mm W x 9.5mm L, with a 4mm screw and a 17mm stem, and they are made of white nylon. OEM manufacturer references are 75522-611-000, 97606-B0700, 99901-0412, and MS-48001.

Screw grommets fit an 8mm square hole. No OEM manufacturer reference is specified.

Screw grommets fit a 12mm round hole and have a 10mm stem and a 16mm head diameter, and they are specified for tall light housing applications. OEM manufacturer reference is 6504072.

Splash shield screw grommets have a 15mm stem, an 18mm x 20mm head size, and a 5.5mm screw, and they are made of black nylon. OEM manufacturer reference is K479-50-AF4.

Screw grommets fit a 10mm x 12.5mm hole and have a 20mm square flange and a 4.2mm screw, and they are specified for headlamp mount and grille opening applications. OEM manufacturer reference is YS4Z-13N129-AA.

Screw grommets fit a 9mm square hole and have a 14mm flange with a panel range of 0.7mm–2.5mm, and they are specified for front bumper applications. OEM manufacturer reference is 1318908-9.

Screw grommets fit an 8.5mm square hole and have a 16mm flange and an 11mm overall length with a panel range of 1.5mm. OEM manufacturer reference is 01281-00831.

Screw grommets use a 4.8mm (No. 10) screw and have a 16mm x 16mm head size, a 7mm stem diameter, and a 7mm stem length. OEM manufacturer reference is 90107-S0X-A01.

Screw grommets have a 15mm x 27mm head size and a 13mm stem length and use a 4.8mm (No. 10) screw, and they are specified for cowl vent applications. OEM manufacturer references are 3M8Z-17C432-A and GK2A-50-798.

Screw grommets have a 15mm head size and a 24mm stem length and use a 4.8mm (No. 10) screw, and they are specified for front bumper applications. OEM manufacturer reference is W703819-S300.

Screw grommets have an 11.5mm x 15.5mm head size and an 18mm stem length and use a 4.8mm (No. 10) screw, and they are specified for side marker/tail light applications. OEM manufacturer reference is W705850-S300.

Specialty grommets have a 16mm x 15mm head size and a 22mm stem length and use a 6.3mm–1.81mm (No. 14) screw, and they are specified for license plate and tail light applications. OEM manufacturer reference is W711031-S300.

Specialty grommets have a 15mm x 18mm head size and a 23mm stem length and use a 6.3mm–1.81mm (No. 14) screw, and they are specified for rear bumper screw w/sealer applications. OEM manufacturer reference is 25704358.

Screw grommets have an 18mm head size and a 28mm stem length and use a 4.8mm (No. 10) screw, and they are made of natural nylon. OEM manufacturer reference is 86910-21010.

Screw grommets/sealer have a 19mm stem length with an 18mm x 18mm top head and an 18mm bottom head, and they use a 4.8mm (No. 10) screw. OEM manufacturer reference is 80625-S300.

Screw grommets have a 17.5mm x 30mm head size and a 10mm stem length and use a 5.5mm (No. 12) screw, and they are made of white nylon. OEM manufacturer reference is 52535-30150.

Screw grommets fit a 7mm round hole and have a 9mm x 9mm head size and a 14mm stem length and use a 2.9mm (No. 4) screw. OEM manufacturer reference is 90189-04207.

Screw grommets have a 20mm head size and a 15mm stem length and use a 4.2mm (No. 8) screw, and they are made of natural nylon. OEM manufacturer reference is 01281-00691.

Screw grommets/sealer have a 16mm head size and a 20mm stem length and use a 4.2mm (No. 8) screw, and they are made of natural nylon. OEM manufacturer reference is 01281-00691.

Screw grommets w/sealer have a 9.5mm x 9.5mm head size and a 16mm stem length and use a 3.5mm (No. 6) screw, and they are made of white nylon. OEM manufacturer reference is 01281-00501.

Screw grommets w/sealer have a 15mm x 19mm head size and a 16mm stem length and use a 6.3mm (No. 14) screw, and they are made of brown nylon. OEM manufacturer references are 01553-2J000 and 26557-2J001.

Screw grommets fit a 7mm square hole and have a 12mm head size and a 15mm stem length and use a 4.8mm (No. 10) screw. OEM manufacturer reference is 90930-0015.

Screw grommets fit an 8mm square hole and have a 12mm head size and an 8mm stem length and use a 4.8mm (No. 10) screw. OEM manufacturer reference is 90481-FA010.

Screw grommets fit an 8mm square hole and have an 11mm head size and an 11mm stem length and use a 3.5mm (No. 6) screw. OEM manufacturer reference is 62731-FA010.

Screw grommets w/sealer have a 16mm x 16mm head size and a 19mm stem length and use a 4.8mm (No. 10) screw, and they are specified for rear bumper reinforcement beam applications. OEM manufacturer reference is 57750-FC010.

Screw grommets w/sealer have a 20mm head size and a 15mm stem length and use a 5.8mm (No. 12) screw. OEM manufacturer reference is 91084-AA010.

Screw grommets fit a 9mm x 9mm hole and have a 22mm head size and a 22mm stem length and use a 5.5mm (No. 12) screw. OEM manufacturer reference is 90189-06177.

Screw grommets fit a 9mm x 9mm hole and have a 20mm head size and a 17mm stem length and use a 5.5mm (No. 12) screw. OEM manufacturer reference is 90189-A0002.

Screw grommets fit a 9mm x 9mm hole and have a 16mm head size and a 16mm stem length and use a 5.5mm (No. 12) screw. OEM manufacturer reference is 90189-06145.

Screw grommets w/sealer fit a 7mm square hole and have a 10mm x 10mm head size and a 12mm stem length and use a 3.2mm (No. 6) screw. OEM manufacturer reference is 90189-04102.

Screw grommets have a 12.5mm stem length and an 11mm head size and use a 4.8mm (No. 10) screw, and they are made of black nylon. OEM manufacturer reference is 811-807-577-C.

Screw grommets have a 12mm stem length and an 11mm head size and use a 4.8mm (No. 10) screw, and they are made of natural nylon. OEM manufacturer reference is 165-827-592.

Screw grommets fit a 6.5mm x 8mm hole and have a 12mm head size and a 15mm stem length and use a 4.8mm (No. 10) screw. OEM manufacturer reference is 6N0-809-968A.

Head air deflector grommet is specified for front fender applications and has a 23mm stem length, and it is made of black nylon. OEM manufacturer reference is 15733970.

____________________________________________________________________________

Nuts 

Expansion nut kit components are used in thin materials where wood screws and sheet metal screws will not hold, a condition frequently encountered during body panel and trim attachment work in body shops serving Spring Valley, New York.

Expansion nut kit components are used for mounting fixtures to cars and trucks, are OE on GMC and Chevy trucks, and install blind from one side.

Automotive mirror nut hardware uses an expansion-style nut for rear view mirror mounting applications. 

Expansion nut kit contents include 25 pieces consisting of Ø17/165 nuts and stainless steel screws. 

Replacement stainless steel screw hardware uses a special stainless steel screw with a nylon washer that will not hurt painted surfaces. 

Expansion nut kit installation requires drilling a 7/16 hole, inserting the nut with the flange side out, inserting the screw and tightening to collapse the legs of the nut, removing the bolt, mounting the fixture, and retightening. 

Expansion nut kit thread size is 1/4-20, and the hole size required is 7/16.

Heavy duty steel clinch-nut threaded inserts install in practically any material. Heavy duty steel clinch-nut threaded inserts are used in any thickness material, from .030 to infinity, and provide strong load bearing threads.

Clinch-nut installation uses a one piece design consisting of a nut portion and a sleeve portion. 

Clinch-nut installation uses a rotating tool mandrel that exerts a pull and draws the nut portion into the sleeve, drawing it into the parent material. 

Clinch-nut installation expands the sleeve when the nut portion is drawn in, creating a strong swage against the parent material.

Heavy duty installation tool equipment is simple to use. Heavy duty installation tool equipment adapts to new installation of any size Clinch-Nuts or Rivet-Nuts, and adapters are ordered separately.

Light duty installation tool equipment is a time and money saver. Light duty installation tool equipment makes quick, quality repairs in the field.

Heavy duty clinch-nut installation tool adapters include pre-assembled hex nose piece assemblies and quick change tool nose piece holders to make installation fast and easy.

Clinch-nut threaded inserts are provided as threaded insert hardware for installation with appropriate tools.

Rivet-nut blind threaded rivets are used in light-gauge materials of metal, plastic, and rigid composition. 

Rivet-nut blind threaded rivets are tubular rivets with internal threads that can be accommodated from one side in seconds. 

Rivet-nut blind threaded rivets are ready to use after installation, with clean threads available for screw attachments. 

Rivet-nut blind threaded rivets are used for materials .010 through .125 in. thickness. 

Rivet-nut blind threaded rivets are available in standard heads that are surface mounted and extend slightly above the material in which they are installed, and expanded heads (small flanged) are also available for flush or 120 degree countersunk installations or wherever a smaller head may be required.

Rivet-nut and clinch-nut tool selection requires proper tool selection based on insert design. 

Rivet-nut and clinch-nut tool selection allows both Rivet-Nut tools, heavy duty Clinch-Nut tools, and light duty installation tools to install threads. 

Rivet-nut and clinch-nut tool selection recommends that a Clinch-Nut tool (hydraulic) be used for Clinch-Nut installation and that a Rivet-Nut tool be used for Rivet-Nut Insta-Thread installations.

Rivet-nut tool equipment includes a mandrel and a nosepiece.

Hex flange nut hardware uses a flange style with a serrated washer face. Hex flange nut hardware is case hardened, slotted, and finished with black oxide finish.

JIS hex lock nut hardware is case hardened, slotted, and finished with black oxide finish.

Hex washer nut hardware uses a flange style with a smooth washer face. Hex washer nut hardware is case hardened, used for universal applications, and finished with black oxide finish and zinc yellow.

Hex nut with free spinning washer hardware uses washer points that provide positive locking action. 

Hex nut with free spinning washer hardware is used for universal applications and is non-locking.

Brass manifold nut hardware is used for manifold and universal applications. 

Brass manifold nut hardware uses a high strength copper-zinc formulation, is corrosion resistant, and has burr-free threads. 

Brass manifold nut hardware includes slot different metric sizes from 6mm to 10mm.

Thread cutting nut hardware includes a stamped hex nut that is self threading with locking tabs, uses a 3/8 stud, uses a 5/8 washer, and has a zinc finish for universal use. 

Thread cutting nut hardware also includes a stamped hex nut that is self threading with no sealer, uses a 4mm stud, uses a 5mm hex with a 15mm integral faceted washer, and is specified for GM 1977-on and universal use. 

Thread cutting nut hardware also includes a stamped hex nut that is self threading with no sealer, uses a 5mm stud, uses a 10mm hex with a 15mm integral faceted washer, and is specified for GM 1977-on and universal use.

Pal nut hardware is vibration proof and reusable. 

Pal nut hardware uses the same wrench size as standard nuts. 

Pal nut hardware is provided in a regular style for threaded fasteners and a thread cutting style for studs. 

Pal nut hardware uses a formed washer face that holds in place.

Pal lock nut hardware is vibration proof.

 Pal lock nut hardware is used on top of standard nuts as a double lock.

Push nut retainer hardware is made from spring steel and provides positive locking. 

Push nut retainer hardware pushes on a stud for fast and easy permanent installation, will not loosen, and is not reusable.

Push nut bolt retainer hardware holds fasteners in place when hands cannot reach. 

Push nut bolt retainer hardware is installed by inserting a cap screw through a panel and threading a nut bolt retainer onto the threads, and the cap screw remains securely in place while hanging outside the panel and while starting nuts.

Metric push nut retainer hardware is finished with zinc.

Metric push nut bolt retainer hardware is finished with dichromate and zinc.

Well nut hardware is a flanged neoprene bushing with a captive brass nut. 

Well nut hardware is designed to provide a shock and vibration resistant fixing for engineering structures. 

Well nut hardware is a combination blind screw anchor suitable for applications of many kinds. 

Well nut hardware swells at the rubber flange on distension to collapse steel up to 16.5mm thick. 

Well nut hardware provides a high rate of radial expansion that allows use in blind holes in solid materials.

Jack nut expansion nut hardware includes a boxed back mounting jack nut with a bronze finish with aluminate, a 6mm-1.0 thread, a 15.8mm head, an 11.1-11.43mm hole, a 3.8-4.75mm grip range, an 18.57mm overall length, and GM universal application. 

Jack nut expansion nut hardware also includes a mirror mounting jack nut with a chrome finish, a 1/4-20 thread, a .625 head, a .434-.450 hole, a .015-.187 grip range, a .731 overall length, and universal application. 

Jack nut expansion nut hardware also includes headlamp bezel and grille nuts that fit an 8mm x 9mm hole, use a 12mm W x 12mm size, use a 5mm screw size, and are made of natural nylon. 

Jack nut expansion nut hardware also includes headlight bezel nuts that fit a 1/4 square hole, use screw size (No. 8 or No. 10), and are made of natural nylon. 

Jack nut expansion nut hardware also includes headlight nuts that fit 10.5mm x 11mm, have a head size of 15mm x 15mm, have a stem length of 10mm, and use a 5.5mm (No. 12) screw size. 

Jack nut expansion nut hardware also includes headlight nuts that fit a 10mm hole, have a head size of 14mm x 18.5mm, have an overall length of 15mm, and are used as a headlight adjusting nut. 

Jack nut expansion nut hardware also includes specialty inserts with sealer that have a head size of 13mm, a hex size of 9.5mm, and a grip range of 5mm-4.2mm.

Speed nut and cage nut hardware includes 1/4-20 nuts with a panel range of .032-.093, a center of hole to edge of 1/2, and a phosphate finish. 

Speed nut and cage nut hardware also includes 1/4-20 nuts with a panel range of .058-.093, a center of hole to edge of 9/16, and a phosphate finish. 

Speed nut and cage nut hardware also includes 1/4-20 nuts with a panel range of .050-.090, a center of hole to edge of 9/16, and a phosphate finish. 

Speed nut and cage nut hardware also includes speed nuts with a panel range of .060-.110, a center of hole to edge of 9/32, and a phosphate finish. 

Speed nut and cage nut hardware also includes speed nuts with a panel range of .025-.040, a center of hole to edge of 9/32, and a phosphate finish. 

Speed nut and cage nut hardware also includes speed nuts with a panel range of .020-.045, a center of hole to edge of 3/16, and a phosphate finish. 

Speed nut and cage nut hardware also includes speed nuts with a panel range of 1/2. 

Speed nut and cage nut hardware also includes speed nuts with a panel range of .024-.056, a center of hole to edge of 15/32, and a phosphate finish. 

Speed nut and cage nut hardware also includes square cage nuts with a 1/4-20 thread and a panel range of .093-.126. 

Speed nut and cage nut hardware also includes square cage nuts with a 5mm-.8mm thread and a panel range of 2.4mm-3.2mm. 

Speed nut and cage nut hardware also includes square cage nuts with a 6mm-1.0mm thread and a panel range of 2.4mm-3.2mm. 

Speed nut and cage nut hardware also includes square cage nuts with a 5mm-1.25mm thread and a panel range of 1.6mm-2.4mm.

Flat speed nut hardware includes flat speed nuts for sheet metal screws with screw size (No. 6) and a phosphate finish. 

Flat speed nut hardware also includes flat speed nuts for sheet metal screws with screw size (No. 8), a 13/32 x 5/8 size, and a phosphate finish. 

Flat speed nut hardware also includes flat speed nuts for sheet metal screws with screw size (No. 10), a 1/2 x 7/8 size, and a phosphate finish. 

Flat speed nut hardware also includes flat speed nuts for sheet metal screws with screw size (No. 14) and a phosphate finish. 

Flat speed nut hardware also includes flat speed nuts for machine screws with screw size 6-32, a 5/16 x 1/2 size, and a phosphate finish. 

Flat speed nut hardware also includes flat speed nuts for machine screws with screw size 8-32, a 1/2 x 7/8 size, and a phosphate finish. 

Flat speed nut hardware also includes flat speed nuts for machine screws with screw size 3/16, a 7/16 x 3/4 size, and a phosphate finish. 

Flat speed nut hardware also includes flat speed nuts for machine screws with screw size 1/4-20, a 9/16 x 1 size, and a phosphate finish.

Push-on stud retainer hardware includes push-on retainers for studs with a stud size of 1/16, a 7/32 x 3/8 size, and a phosphate finish. 

Push-on stud retainer hardware also includes push-on retainers for studs with a stud size of 3/32, a 1/4 x 7/16 size, and a phosphate finish.

Push-on nuts for studs are specified with a stud size of 1/8 and a 5/16 x 9/16 size, and they have a phosphate finish. 

Push-on nuts for studs are specified with a stud size of 3/16 and a 3/8 x 9/16 size, and they have a phosphate finish. 

Push-on nuts for studs are specified with a stud size of 5/16 and a 3/8 x 5/8 size, and they have a phosphate finish. 

Push-on nuts for studs are specified with a stud size of 7/32 and a 7/16 x 5/8 size, and they have a phosphate finish.

Flanged speed nuts are specified for a screw size of No. 4 and are intended for sheet metal screws.

Radiator grille nuts fit a 1/4 square hole.

Nylon nuts for radiator grille applications are specified for a screw size of No. 8 and are made of white nylon.

Body nuts are specified for a screw size of No. 8 and are intended for side marker, headlamp, and fender panel use, and they are made of natural nylon.

License plate nuts fit 3mm and 3/16 and are specified for a screw size of 6mm (1/4 on No. 14), and they are nylon push nuts. 

License plate nuts fit 4mm and 5mm (No. 12) and are specified for a screw size of 4.2mm (No. 10), and they are made of nylon. 

License plate nuts fit 4mm and 5mm (No. 12) and are made of black nylon. 

License plate nuts are specified for a screw size of No. 6 or No. 8 and are intended for headlight bezel use, and they are made of natural nylon.

 License plate nuts are specified for a screw size of No. 14 and are intended for front and rear use. 

License plate nuts fit a 3/8 hole and are specified for a screw size of 1/4 (No. 14), and they are intended for door lock remote control use, and they are made of natural nylon. 

License plate nuts have a hex of 10mm (25/64) and are made of nylon.

Side marker nuts are specified for a screw size of No. 8 and are intended for headlight door and grille use, and they are made of white nylon.

Moulding nuts have an overall size of 18mm x 15mm, a stud size of 5mm, a hex of 10mm, and a flange nut design.

Front bumper nylon nuts have a stem of 11mm, are specified for a screw size of 5.5mm (No. 12), and are made of natural nylon.

Nylon nuts fit 8mm x 13mm and have a head size of 16mm and a stem length of 7mm, and they are made of natural nylon. 

Nylon nuts have a stem length of 11mm, are specified for a screw size of 4.2mm (No. 8), and are made of white nylon. 

Nylon nuts have a stem diameter of 9mm x 11mm and an overall length of 13.5mm, and they are made of white nylon. 

Nylon nuts fit 6mm nylon and have a head size of 16mm x 10mm, are specified for a screw size of 3.5mm (No. 6), and have a stem length of 7mm. 

Black nylon nuts fit an 8.5mm hole and have a head size of 15mm, are specified for a screw size of 5.5mm (No. 12), and have a stem length of 8mm. 

Nylon nuts have a head size of 4.8mm x 14mm, are specified for a screw size of 4mm (No. 10), and have a stem length of 7mm. 

Nylon nuts fit 7mm nylon and have a head size of 17mm hole, are specified for a screw size of 3.5mm (No. 6), and have a stem length of 7mm. 

Nylon nuts fit 7mm nylon and have a head size of 17mm hole, are specified for a screw size of 3.5mm (No. 6), and have a stem length of 7mm. 

Nylon nuts fit 7mm nylon and have a head size of 17mm hole, are specified for a screw size of 3.5mm (No. 6), and have a stem length of 7mm. 

Nylon nuts fit 7mm nylon and have a head size of 17mm hole, are specified for a screw size of 3.5mm (No. 6), and have a stem length of 7mm. 

Nylon nuts fit 7mm nylon and have a head size of 17mm hole, are specified for a screw size of 3.5mm (No. 6), and have a stem length of 7mm.

Rear push nuts are specified with a stud of 4.5mm and an OD of 22mm, and they are for plastic studs in wheel opening applications.

Thread cutting nuts have a thread of 5/16 and are sheet metal nuts.

Zinc sheet metal nuts are specified for a screw size of 4mm x 19mm, have an overall size of 18mm x 16mm, and have a zinc finish.

Specialty nuts are specified for a screw size of 3mm x 13mm, have a stem length of 8mm, and have a zinc finish. 

Specialty nuts fit 6mm x 14mm and are specified for a screw size of 4.2mm (No. 8), and they are intended for center console, instrument panel, light, and grille applications.

Specialty push nuts are specified for a screw size of 4mm x 16mm, have an overall size of 22mm x 14mm, and are intended for front bumper specialty nut applications.

Radiator grille nuts fit 10mm (No. 8) and have a zinc phosphate finish.

Specialty nylon nuts have an overall of 22mm and a stud size of 8, and they are intended for cowl vent and fender apron applications.

Metric class 8 hex nuts have a pitch of 1.25, a hex of 14mm, a zinc finish, a steel material specification, and a DIN 934 specification.

Split collar lock nuts have a pitch of 1.50mm, a hex of 14mm, and a copper plated steel material specification.

Flanged tubular nuts fit 8mm and have a head size of 16mm, a stem length of 16mm, and a stud size of 7mm, and they are black.

Nylon flange nuts have an overall height of 10mm and a hex size without flange of 14mm, and they are made of black nylon.

Fender bracket retaining nuts are specified for a screw size of 4.8mm and a panel range of .5-3.1mm, and they are made of black nylon.

Extruded U nuts are specified for a screw size of M6 x 1.0, a panel range of 3-4mm, and a center of hole to edge of 15mm, and they are intended for wheel housing applications, and they are black. 

Extruded U nuts are specified for a screw size of M5 x .8, a depth of 15mm, and a panel range of 2-4mm, and they are intended for fender wheel and general usage.

Phosphate extruded U nuts are specified with a thread size of 1/4-20, a panel range of .025-.125, and a center of hole to edge of 15/32. 

Phosphate thread extruded U nuts are specified with a thread size of 1/4-20, a panel range of .125-.156, and a center of hole to edge of 25/32. 

Phosphate thread extruded U nuts are specified with a thread size of 1/4-20, a panel range of .025-.125, and a center of hole to edge of 5/8. 

Phosphate thread extruded U nuts are specified with a thread size of 1/4-20, a panel range of .125-.156, and a center of hole to edge of 7/8. 

Phosphate thread extruded U nuts are specified with a thread size of .205-.260, a panel range of .025-.125, and a center of hole to edge of 3/4.

Extruded U nuts are specified for a screw size of 10mm-1.50mm, a panel range of 1.0mm-6.0mm (.040-.230), and a center of hole to edge of 19mm (3/4), and they have a phosphate finish. 

Extruded U nuts are specified for a screw size of .80mm-1.50mm, a panel range of 0.8mm-4.0mm (.030-.160), and a center of hole to edge of 15mm (17/32), and they are NQ locking.

Screw extruded U nuts are specified for a screw size of 8mm-1.25mm, a panel range of .8mm-4.0mm (.030-.160), and a center of hole to edge of 15.8mm (5/8), and they have a phosphate finish. 

Screw extruded U nuts are specified for a panel range of 2mm-1.0mm, a screw size of 8mm-1.25mm, and a center of hole to edge of 14.5mm (9/16), and they have a zinc organic finish.

Extruded U nuts are specified for a screw size of 4.8mm (#8), a panel range of 2.5mm-3.8mm (.098-.150), and a center of hole to edge of 9.5mm (3/8), and they are locking.

Extruded U-nut uses an 8.0mm-1.25mm screw size and fits a panel range of 2.5mm-3.8mm (.098-.150). The center of hole to edge dimension is 15.9mm (5/8). The finish is phosphate. The application is bumper impact strip fascia.

Sheet metal extruded U-nut uses a 6.3mm-1.0mm screw size and fits a panel range of 0.8mm-1.6mm. The application is fender and front.

Wide range U-nut uses a .8-1.25 screw size and fits a panel range of .025-.150. The center of hole to edge dimension is 5/8. The finish is phosphate.

Wide range U-nut uses a .8-1.25 screw size and fits a panel range of .125-.250. The center of hole to edge dimension is 3/8. The finish is phosphate.

Wide range extruded U-nut uses a 4.8mm (#8) screw size and fits a panel range of .025-.150. The center of hole to edge dimension is 17/32. The finish is phosphate.

S-nut uses a 5mm (No. 12) screw size and fits a panel range of 5.5mm (7/32). The center of hole to edge dimension is 12mm. The material is orange nylon.

U-nut uses a 6.3mm (No. 14) screw size and fits a panel range of 6.3mm. The center of hole to edge dimension is 14mm. The material is black nylon.

U-nut uses a 4.8mm (No. 10) screw size and fits a panel range of .8mm-2.0mm. The center of hole to edge dimension is 10mm. The material is black nylon.

U-nut uses a 4.8mm (No. 10) screw size and fits a panel range of .8mm-2.0mm. The center of hole to edge dimension is 10mm. The material is gray nylon.

Metric extruded U-nut uses a 6.3mm (No. 14) screw size and fits a panel range of .8mm-1.6mm. The center of hole to edge dimension is 11mm. This fastener has a short throat.

Metric extruded U-nut uses an M5.1 screw size and fits a panel range of 0.80mm-4.0mm. The center of hole to edge dimension is 19.5mm. The finish is phosphate.

Metric extruded U-nut uses a 6.3mm-1.0mm screw size and fits a panel range of 8.0mm-4.0mm (.030-.160). The center of hole to edge dimension is 14.5mm (9/16). The finish is phosphate.

Metric extruded U-nut uses an 8mm-1.25mm screw size and fits a panel range of 8.0mm-4.0mm (.030-.160). The center of hole to edge dimension is 14.5mm (9/16). The finish is phosphate.

Extruded U speed nut has a center of hole to edge dimension of 13mm and fits a panel range up to 1mm. The screw size is 5mm (No. 10). The finish is zinc. The application is inner fender clip.

Nylon U-nut uses a 6mm (No. 14) screw size and fits a panel range up to 1.5mm. The center of hole to edge dimension is 8mm. The material is black nylon.

Nylon U-nut fits a panel range up to 4mm and uses a captive metal hex nut of 6mm. The center of hole to edge dimension is 14mm. The material is black nylon.

Nylon U-nut uses a 6mm (No. 14) screw size and fits a panel range up to 2mm. The center of hole to edge dimension is 12mm. The application is left/right front bumper.

Nylon U-nut uses a 6mm (No. 14) screw size and fits a panel range up to 2mm. The center of hole to edge dimension is 12mm. The application is rear bumper.

Nylon U-nut uses a 5.5mm (No. 12) screw size and fits a panel range up to 2mm. The center of hole to edge dimension is 11mm. The application is front fender liner.

Nylon U-nut uses a 4.8mm (No. 10) screw size and fits a panel range up to 2mm. The center of hole to edge dimension is 7mm. The application is front fender liner and mudguard.

U speed nut uses a (No. 6) screw size and fits a panel range of 0.25-1.25. The center of hole to edge dimension is 3/8. The finish is phosphate.

U speed nut uses a 4.2mm screw size and fits a panel range of 0.25-0.40. The center of hole to edge dimension is 1/4. The finish is phosphate.

U speed nut uses a (No. 10) screw size and fits a panel range of 0.20-0.51. The center of hole to edge dimension is 15/32. The finish is phosphate.

U speed nut uses a 1/4-20 screw size and fits a panel range of 0.64-1.25. The center of hole to edge dimension is 9/16. The finish is phosphate.

U speed nut uses a 4.2mm (No. 8) screw size and fits a panel range of 3mm-4mm. The depth is 7mm. The center of hole to edge dimension is 7mm.

U speed nut uses a 4.2mm (No. 8) screw size and fits a panel range of 5mm-1.7mm. The depth is 7mm. The center of hole to edge dimension is 8mm.

U speed nut uses a 4.2mm (No. 8) screw size and fits a panel range of 5mm-2.5mm. The depth is 8mm. The center of hole to edge dimension is 8mm.

U speed nut uses a 4.8mm screw size and fits a panel range of 8mm-1.7mm. The depth is 8mm. The center of hole to edge dimension is 11mm.

U speed nut uses a 4.8mm screw size and fits a panel range of 9mm-2mm. The depth is 8mm. The center of hole to edge dimension is 8mm.

U speed nut uses a 4.8mm screw size and fits a panel range of 5.5mm-1.7mm. The depth is 7mm. The center of hole to edge dimension is 7mm.

U speed nut uses a 5.6mm screw size and fits a panel range of 1.2mm-2.0mm. The depth is 10mm. The center of hole to edge dimension is 10mm.

U speed nut uses a 6.3mm screw size and fits a panel range of 7mm-1.5mm. The depth is 13mm. The center of hole to edge dimension is 14mm.

U speed nut uses a 6.3mm screw size and fits a panel range of 0.25-1.50. The depth is 14mm.

U speed nut uses a 4.2mm (No. 8) screw size. The depth is 5mm.

U speed nut uses an 8-18 screw size and fits a panel range of 0.25-1.50.

U speed nut uses a 4.2mm (No. 8) screw size and fits a panel range of 4mm-2.5mm. The center of hole to edge dimension is 14mm. The finish is zinc and yellow.

U speed nut uses a (No. 10) screw size and fits a panel range of 0.25-1.50. The application is universal/general purpose.

____________________________________________________________________________

Retainers 

Retainer clips have a head size of 14mm and a stem length of 9mm. They are used on the door side panel and in the luggage compartment.

Weatherstrip clips have a top head diameter of 9mm, a bottom head diameter of 12mm, a stem diameter of 7mm, and a stem length of 13mm.

Front cowl retaining clips have a head size of 13mm, a stem diameter of 6mm, and a stem length of 10mm. They are made of black nylon.

Trim panel and dash console clips are retainers made of white nylon.

Hood to cowl top seal retainer clips have a head size of 17 mm × 13 mm, a stem diameter of 7 mm, and a stem length of 13 mm, and are made of black nylon, specifications commonly encountered during weatherstrip and cowl seal service work in body shops operating in and around Goshen, New York.

Nylon and metal retainers have a size of 14.5mm x 47mm and an overall length of 43mm. They are made of black phosphate plated steel and are used on the front and rear door.

Moulding retainer clips have a head size of 13mm x 26mm and a stem length of 25mm. They are made of white nylon.

Slide door moulding retainers have a head size of 3/8″, a stem diameter of 3/32″, and a stem length of 1/2″.

Door trim panel and headliner retainers have a top head diameter of 11/16″, a bottom head diameter of 3/4″, a stem diameter of 1/4″, and a stem length of 1/2″.

Door trim, back panel, and lower garnish retainers have a top head diameter of 13mm, a bottom head diameter of 18mm, a stem diameter of 5mm, and a stem length of 17mm.

Slide door trim panel retainers have a top head diameter of 15mm, a bottom head diameter of 20mm, a stem diameter of 5mm, and a stem length of 14mm.

Grille to fascia retainers have a phosphate finish.

Trim plug retainers have a head size of 15mm x 17mm, a stem length of 7mm, and an overall length of 11mm. They are used as a door latch trim grommet.

Tail lamp grommets with sealer fit a 9mm x 6mm hole and have a head diameter of 13mm x 20mm and an overall length of 19mm. They are made of blue nylon.

Screw grommets fit 9mm square holes and have a flange of 16mm and a screw size of 5mm. They are used on the front and rear wheel fender liner.

Specialty inserts with sealer have a head diameter of 6mm–10mm and a hex size of 17mm. They are head grommets with a grip range of 7mm–31mm.

Interior trim and garnish retainers have a head size of 7/16″, a stem diameter of 5/16″, and a stem length of 1/2″. They are made of blue nylon.

Moulding retainers have a head size of 13mm x 13mm and accept a screw size of 3.5mm (No. 6). They have a stem diameter of 13.5mm and a length of 8mm.

Grille retainer nuts have an overall height of 7mm and a hex of 13mm. They are grille retainer nuts made of black nylon.

Side and rear door trim retainers have a top head diameter of 13mm, a bottom head diameter of 24 x 7/8, a stem diameter of 5/16″, and a stem length of 3/4.

Shield retainers have a head size of 3/4″, a stem diameter of 5/16″, and a stem length of 1-1/16. They are used on the tailgate, harness, wiring, and E-cleaner.

Shield retainers fit a 15/64 (6mm) hole.

Shield retainers fit a 7/64 (2.5mm) hole.

Shield retainers fit a 5/16 (7.8mm) hole.

Shield retainers have a head size of 23/64, a stem diameter of 3/16, and a stem length of 7/16. They are made of black nylon.

Shield retainers fit a 9/64 (3.5mm) hole and are made of black nylon.

Shield retainers have a head size of 5/8, a stem diameter of 1/4, and a stem length of 3/4. They are used on the fender and bumper.

Drive rivet retainers fit a 5mm hole and have a weather face of 7mm. They are used on the taillight lens.

Front fender retainers fit a 10mm hole and have an overall height of 18mm. They are used on the front fender and are made of dark and light gray nylon.

Moulding clips have a head size of 1/2, a stem diameter of 3/32, and a stem length of 11/16. They are used on the rear window.

Panel retainers for front and back locations have a head size of 25/32, a stem diameter of 5/16, and a stem length of 15/16. They are made of black nylon.

Rocker panel and garnish retainers fit a 7mm hole and have a head diameter of 20mm and a stem length of 8mm. They are made of black nylon.

Drive type rivet retainers fit a 1/4 (6.4mm) hole and have a head diameter of 7/16 (11mm) and a stem diameter of 7/32 (5.5mm). They are used on the splash shield and fascia.

Drive type rivet retainers fit a 5/16 (8mm) hole and have a head diameter of 1/2 (12.7mm) and a stem diameter of 7/32 (5.5mm). They have a shoulder of 5/16 (8mm).

Drive type rivet retainers fit a 1/4 (6.4mm) hole and have a head diameter of 7/16 (11mm) and a stem diameter of 7/32 (5.5mm). They are made of black nylon.

Drive type rivet retainers fit a 1/4 (6.4mm) hole and have a head diameter of 11/16 (17.5mm) and a stem diameter of 5/16 (8mm). They are used on the cowl ledge, weatherstrip, and fender liner.

Drive type rivet retainers fit a 7mm hole and have a head diameter of 15mm and a stem diameter of 23mm. They are used on the fascia.

Drive type rivet retainers fit a 6mm hole and have a head diameter of 15mm and a stem diameter of 23mm. They are used on the fascia.

Drive type rivet retainers fit a 1/2 (12.7mm) hole and have a head diameter of 15/16 (24mm) and a stem diameter of 15/16 (24mm). They have a shoulder of 3/8 (9.2mm).

Drive type rivet retainers fit a 5mm hole and have a washer face of 15mm. They are used for trim attachments.

Drive type rivet retainers fit a 9/32 (7mm) hole and have a head diameter of 17/16 (17mm) and a stem diameter of 7/16 (11mm). They are used on the grille.

Drive type rivet retainers fit a 5/16 (8mm) hole and have a head diameter of 21/32 (16.7mm) and a stem diameter of 9/16 (14.3mm). They are used on the radiator overflow bottle.

Drive type rivet retainers fit a 1/8 (3.2mm) hole and have a head diameter of 1/2 (12.7mm) and a stem diameter of 1/2 (12.7mm). They are used on the bumper fascia.

Drive type rivet retainers fit a 9.5mm (3/8) hole and have a head diameter of 18mm and a stem diameter of 23mm. They are used on the front bumper fascia.

Drive type rivet retainers fit a 1/4 (6.4mm) hole and have a head diameter of 13/32 (10.5mm) and a stem diameter of 1/4 (6.4mm). They are used on the rear door panel.

Drive type rivet retainers fit a 9mm hole and have a head diameter of 21mm and a stem diameter of 21mm. They are used on the rear bumper cover.

Drive type rivet retainers fit a 5/16 (8mm) hole and have a head diameter of 23/32 (18.3mm) and a stem diameter of 29/32 (23mm). They are used on the fascia.

Drive type rivet retainers fit a 1/4 (6.4mm) hole and have a head diameter of 7/16 (11mm) and a stem diameter of 5/16 (8mm). They are used on the front bumper fascia.

Drive type retainers fit a 10mm hole and have a head diameter of 20mm and a stem diameter of 18mm. They are used on the front and rear bumper.

Drive type retainers fit a 10mm hole and have a head diameter of 20mm and a stem diameter of 13mm. They are made of black nylon.

Drive type retainers fit a 7mm hole and have a head diameter of 17mm and a stem diameter of 9mm. They are made of black nylon.

Drive type retainers fit an 8mm hole and have a head diameter of 20mm and a stem diameter of 8mm. They are made of black nylon.

Drive type retainers fit an 8mm hole and have a head diameter of 20mm and a stem diameter of 20mm. They are used on the front fender.

Drive type retainers fit a 9mm hole and have a head diameter of 19mm and a stem diameter of 25mm. They are made of black nylon.

Drive type retainers fit a 9mm hole and have a head diameter of 15mm and a stem diameter of 12mm. They are used on the bumper cover.

Drive type retainers fit an 8mm hole and have a head diameter of 20mm and a stem diameter of 11mm. They are used on the front fender and bumper support.

Drive type rivet retainers fit a 4.1mm hole and have a head diameter of 16mm (5/8″) and a stem diameter of 4mm (5/32″). They are used on the front fender mud skirt and fender.

Drive type retainers fit an 8mm hole and have a head diameter of 11mm and a stem diameter of 10mm. They are used on the front bumper cover.

Drive type retainers fit a 7mm hole and have a head diameter of 20mm and a stem diameter of 20mm. They are used on the fender splash shield.

Drive type rivet retainers have a head diameter of 24mm and a stem diameter of 14mm. They are used on the radiator light shield.

Drive type rivet retainers fit an 8mm hole and have a head diameter of 18mm and a stem diameter of 12mm. They are used as a bumper clip.

Drive type hole retainers fit a 7mm hole and have a flange of 20mm and a stem length of 8.5mm.

Drive type retainers fit a 7mm hole and have a head diameter of 14mm and a stem diameter of 12mm. They are used on the bumper cover and garnish.

Drive type retainers fit an 8mm hole and have a head diameter of 18mm and a stem diameter of 12mm. They are used on the fender and bumper.

Drive type rivet retainers fit an 8mm hole and have a head diameter of 20mm and a stem diameter of 20mm. They are used on the mud guard.

Drive type retainers fit an 8mm hole and have a head diameter of 16.5mm and a stem diameter of 25mm. They are used on the bumper and rear wheel apron.

Drive type retainers fit an 8mm hole and have a head diameter of 20mm and a stem diameter of 26mm. They are used on the bumper cover and fender shield.

Drive type retainers fit a 7mm hole and have a head diameter of 18mm and a stem diameter of 7mm. They are used on the front fender liner.

Drive type retainers fit a 10mm hole and have a head diameter of 20mm and a stem diameter of 24mm. They are used for grille mounting.

Drive type retainers fit an 8mm hole and have a head diameter of 20mm and a stem diameter of 20mm. They are used for air baffle to under carriage.

Drive type retainers fit a 7mm hole and have a head diameter of 18mm and a stem diameter of 7mm. They are used on the fender liner.

Drive type retainers fit an 8mm hole and have a head diameter of 20mm and a stem diameter of 8mm. They are made of black nylon.

Drive type retainers fit a 9mm hole and have a flange of 18mm, a panel range of 3.5mm–10mm, and a stem length of 31mm.

Drive type retainers fit a 9mm hole and have a flange of 20mm, a panel range of 2mm–6.5mm, and a stem length of 16mm.

Drive type retainers fit a 7mm hole and have a head diameter of 16mm and a stem diameter of 18mm. They are made of black nylon.

Screw type rivet retainers fit a 14.6mm hole and have a head diameter of 34mm and a stem diameter of 14mm. They are used under hood.

Screw type rivet retainers fit a 5/16″ (8mm) hole and have a head diameter of 43.6mm (1-23/32″) and a stem diameter of 23.4mm (29/32″). They are used in the front compartment and spare tire.

Screw type rivet retainers fit a 4.8mm (3/16″) hole and have a head diameter of 9.6mm (3/8″). They are used on the cow panel to reinforcement.

Screw type rivet retainers fit an 8mm hole and have a head diameter of 15mm. They are made of black nylon.

Screw type rivet retainers fit an 8mm hole and have a head diameter of 18mm. They are made of black nylon.

Screw type rivet retainer fits an 11mm hole. The head diameter is 20mm, and the stem diameter is 14mm. This fastener is used on bumper and fascia applications.

Screw type rivet retainer fits a 6mm hole. The head diameter is 9mm, and the stem diameter is 9mm. This fastener is made of black nylon.

Screw type rivet retainer fits a 4.6mm (3/16″) hole. The head diameter is 11mm (7/16″), and the stem diameter is 7mm (9/32″). This fastener is made of black nylon.

Screw type rivet retainer fits a 4.6mm (3/16″) hole. The head diameter is 17mm (11/16″), and the stem diameter is 7mm (9/32″). This fastener is made of black nylon.

Screw type rivet retainer fits a 6mm hole. The head diameter is 22mm (7/8″), and the stem diameter is 21mm (13/16″). This fastener is used on fascia, trim, and grille applications.

Screw type rivet retainer fits a 6mm hole. The head diameter is 14mm (9/16″), and the stem diameter is 11mm. This fastener is made of black nylon.

Screw type rivet retainer fits a 5/16″ (8mm) hole. The head diameter is 15mm (5/8″), and the stem diameter is 13mm. This fastener is made of black nylon.

Screw type rivet retainer fits an 8mm hole. The head diameter is 20mm, and the stem diameter is 9mm. This fastener is made of black nylon.

Screw type rivet retainer fits a 9mm hole. The head diameter is 22mm (7/8″), and the stem diameter is 23mm (29/32″). This fastener is made of black nylon.

Screw type rivet retainer fits a 10mm hole. The head diameter is 19mm, and the stem diameter is 11mm. The panel range is 2mm-7mm.

Screw type rivet retainer fits an 8mm hole. The head diameter is 20mm, and the stem diameter is 20mm. This fastener is used on bumper cover applications.

Screw type rivet retainer fits a 4.6mm (3/16″) hole. The head diameter is 17mm (11/16″), and the stem diameter is 7mm (9/32″). This fastener is made of black nylon.

Screw type rivet retainer fits a 6mm hole. The flange is 18mm. The panel range is 1.6mm-6mm, and the stem length is 17.5mm.

Screw type rivet retainer fits a 6mm hole. The flange is 18mm. The panel range is 1.6mm-6mm, and the stem length is 12mm. This fastener is used on bumper cover applications.

Screw type rivet retainer fits a 6mm hole. The head diameter is 18mm, and the stem diameter is 12mm. This fastener is made of black nylon.

Screw type rivet retainer fits a 9mm hole. The head diameter is 18mm, and the stem diameter is 11mm. This fastener is made of black nylon.

Screw type rivet retainer fits an 8mm hole. The head diameter is 20mm, and the stem diameter is 20mm. This fastener is made of black nylon.

Screw type rivet retainer fits an 8mm hole. The head diameter is 20mm, and the stem diameter is 20mm. This fastener is used on fender splash shield applications.

Screw type rivet retainer fits a 6mm hole. The head diameter is 18mm, and the stem diameter is 12mm. This fastener is used on cowling panel applications.

Control-to-sheet-metal retainer has a top head diameter of 12mm and a bottom head diameter of 15/16. The stem diameter is 5/16, and the stem length is 1-1/8.

Hood seal retaining clip has a head size of 13mm. The stem diameter is 7mm, and the stem length is 11mm. This fastener is made of black nylon.

Headliner retaining clip has a head size of 14mm. The stem diameter is 6mm, and the stem length is 16mm. This fastener is made of black nylon.

Top door panel retainer has a bottom head diameter of 13mm. The stem diameter is 6mm, and the stem length is 9.5mm. This fastener is clear.

Door panel retainer has a top head diameter of 12.5mm and a bottom head diameter of 15mm. The stem diameter is 8mm, and the stem length is 6.5mm.

Door weatherstrip retainer has a stem diameter of 3/16 and a stem length of 5/8. This fastener is made of black nylon.

Interior trim panel retainer has a bottom head diameter of 12.4 and a top head diameter of 13.2. The stem diameter is 1/4, and the stem length is 9/16.

Anti-rattle foam wedge retainer is specified as an anti-rattle foam wedge retaining fastener.

Seat retaining clip has a head size of 20mm. The stem diameter is 11mm, and the stem length is 16mm. The material is black nylon.

Seat retaining clip has a head size of 13mm. The stem diameter is 7mm, and the stem length is 15mm. The material is black nylon.

Grille plate hold down retainer is specified as a grille plate hold down retaining fastener.

Push pin type retainer fits an 8mm square hole. The head diameter is 18mm, and the stem length is 8mm. This fastener is used as a grille retainer.

Front bumper fascia rivet retainer fits a 9.5mm (3/8″) hole. The head diameter is 17mm, and the stem length is 18mm. The shoulder length is 2mm.

Rear bumper fascia retainer fits a 12.7mm (1/2″) hole. The head diameter is 27mm (1-1/16″), and the stem length is 27mm. The shoulder length is 18mm (3/4″).

Door weatherstrip retainer has a head size of 5mm x 15mm. The stem length is 9mm, and the hole size is 5mm. The material is natural nylon.

Door trim panel retainer has a top head diameter of 19/32 and a bottom head diameter of 23/32. The stem diameter is 5/16, and the stem length is 5/8.

Door trim panel retainer has a top head diameter of 15mm and a bottom head diameter of 20mm. The stem diameter is 9mm, and the stem length is 15mm.

Hood seal retainer has a head size of 12mm. The stem diameter is 8mm, and the stem length is 5mm. The material is black nylon.

Bumper push type retainer fits a 10mm hole. The head diameter is 18mm, and the stem diameter is 15mm. The material is black nylon.

Hood to cowl seal retainer has a head size of 6mm x 16mm. The stem length is 15mm, and the hole size is 5mm. The material is white nylon.

Hood seal retaining clip has a head size of 11mm. The stem diameter is 7mm, and the stem length is 6mm. The material is black nylon.

Front air deflector retainer has a top head diameter of 18mm and a bottom head diameter of 26mm. The stem length is 27mm. The material is black nylon.

Door trim panel retainer has a top head diameter of 15mm and a bottom head diameter of 18mm. The stem diameter is 8mm, and the stem length is 14mm.

Door and interior trim panel retainer has a top head diameter of 13mm and a bottom head diameter of 11mm. The stem diameter is 9.5mm.

Door trim panel retainer has a top head diameter of 15mm and a bottom head diameter of 20mm. The stem diameter is 9mm, and the stem length is 18mm.

Door trim panel retainer has a top head diameter of 15mm and a bottom head diameter of 20mm. The stem diameter is 9mm, and the stem length is 18mm.

Door trim panel retainer has a top head diameter of 16mm and a bottom head diameter of 22mm. The stem diameter is 9mm, and the stem length is 15mm.

Door panel retainer has a top head diameter of 20mm, a middle head diameter of 19mm, and a bottom head diameter of 19mm. The stem diameter is 14mm, and the stem length is 16mm. The material is black nylon.

Door panel retainer has a trim thickness of 3mm. The overall length is 23mm, the upper pin head is 13mm, the flange is 24mm, and the panel range is 11mm.

Door panel retainer has a top head diameter of 15mm and a bottom head diameter of 18mm. The stem diameter is 13mm, and the stem length is 15mm.

Door panel retainer fits a 7mm hole. The head diameter is 18mm, and the overall length is 25mm. The panel range is 1.5mm-11.5mm.

Retaining clip has a head size of 30mm. The stem diameter is 4mm, and the stem diameter is 18mm. The material is black nylon.

Head retaining clip has a head size of 13mm. The stem diameter is 7.5mm, and the stem diameter is 15mm. The material is black nylon.

Rocket moulding retainer fits a 9mm hole. The top head diameter is 12mm x 20mm, and the bottom head diameter is 14mm x 20mm. The stem length is 31mm. The material is gray nylon.

Moulding retainer fits a 9mm hole. The top head diameter is 12mm x 20mm, and the bottom head diameter is 14mm x 20mm. The stem length is 31mm. The material is white nylon.

Body side moulding retainer fits a 9mm hole. The head size is 12mm x 20mm. The stem length is 11mm. The material is white nylon.

Rock moldings retainer fits a 3/8 hole. The top head diameter is 3/16 x 2-1/2, and the bottom head diameter is 3/4 x 1-3/2. The stem length is 9/16.

Rock moulding retainer fits a 3/8 hole. The top head diameter is 3/4 x 2-1/2, and the bottom head diameter is 3/4 x 1-3/2. The stem length is 9/16.

Moulding retainer is specified as 11mm x 14mm and is used on the rear bumper.

Cowl vent retainer fits a 7mm hole. The head diameter is 10mm x 14mm. The trim thickness is 2.8mm. The overall length is 18.5mm.

Retainer has a top head diameter of 10mm x 14mm and a bottom head diameter of 18mm. The stem diameter is 9mm. The stem length is 13mm.

Retainer has a head diameter of 18mm. The stem diameter is 9mm. The stem length is 15mm.

Locking retainer has a head diameter of 18.5mm and a stem length of 21mm. The application is a floor mat clip retainer.

Retainer with rubber O-ring has a head diameter of 25mm. The stem diameter is 9.5mm, and the stem length is 16mm. The shoulder diameter is 14mm.

Retainer with sealer has a top head diameter of 14mm, a middle head diameter of 15.5mm, and a bottom head diameter of 18mm. The stem diameter is 9.5mm.

Retainer with sealer has a top head diameter of 12mm and a bottom head diameter of 18mm. The stem diameter is 5mm. The stem length is 16mm.

Retainer has a top head diameter of 18mm and a bottom head diameter of 18mm. The stem diameter is 8mm. The stem length is 18mm.

Retainer has a head size of 36mm. The shoulder height is 28mm. The upper length is 14mm. The application is a bumper retainer.

Light retainer has a top head diameter of 15mm and a bottom head diameter of 18mm. The stem diameter is 9mm. The stem length is 13mm.

Cooler hose clip has an overall height of 24mm and is for 3/4 heater hose. The material is gray nylon.

Trim retainer has a top head diameter of 15mm and a bottom head diameter of 18mm. The stem diameter is 12mm. The stem length is 14mm.

Retainer has a top head diameter of 13mm and a bottom head diameter of 18mm. The stem diameter is 9.5mm. The stem length is 14mm.

Lamp retainer fits an 8mm square hole. The top head diameter is 15mm, and the bottom head diameter is 18mm. The stem length is 12mm.

Panel retainer fits a 9mm hole. The top head diameter is 15mm, and the bottom head diameter is 19.5mm. The grommet flange diameter is 24mm. The stem length is 12mm.

Panel retainer fits a 9mm hole. The top head diameter is 15mm, and the bottom head diameter is 19.5mm. The grommet flange diameter is 24mm. The stem length is 12mm.

Retainer has a top head diameter of 13mm, a middle head diameter of 18mm, and a bottom head diameter of 16mm. The stem diameter is 8mm. The stem length is 13mm.

Retainer has a top head diameter of 14mm and a bottom head diameter of 17mm. The stem diameter is 5mm. The stem length is 14mm.

Retainer has a top head diameter of 14mm and a bottom head diameter of 18mm. The stem diameter is 5mm. The stem length is 14mm.

Retainer with sealer has a top head diameter of 18.5mm and a bottom head diameter of 19.5mm. The stem diameter is 11mm. The stem length is 16mm.

Retainer has a top head diameter of 15mm and a bottom head diameter of 15mm. The stem diameter is 9mm. The stem length is 14mm.

Retainer fits a 10mm square hole. The head size is 18.5mm. The stem diameter is 10mm. The overall length is 32mm.

Trim retainer has a top head diameter of 19mm and a bottom head diameter of 26mm. The stem diameter is 9mm. The stem length is 19mm.

Retainer has a top head diameter of 13mm and a bottom head diameter of 18mm. The stem diameter is 9mm. The stem length is 13mm.

Retainer has a top head diameter of 13mm and a bottom head diameter of 18mm. The stem diameter is 9.5mm. The stem length is 11mm.

Retainer has a top head diameter of 16mm and a bottom head diameter of 13mm. The stem diameter is 5mm. The stem length is 12mm.

Retainer with sealer has a top head diameter of 15mm, a middle head diameter of 16mm, and a bottom head diameter of 18mm. The stem diameter is 5mm. The stem length is 13mm.

Retainer has a top head diameter of 13mm, a middle head diameter of 18mm, and a bottom head diameter of 18mm. The stem diameter is 9mm.

Retainer with sealer has a top head diameter of 13mm, a middle head diameter of 13mm, and a bottom head diameter of 18.5mm. The stem diameter is 10.5mm.

Retainer has a top head diameter of 13mm, a middle head diameter of 13mm, and a bottom head diameter of 18mm. The stem diameter is 9.5mm.

Retainer has a top head diameter of 13mm, a middle head diameter of 13mm, and a bottom head diameter of 18mm. The stem diameter is 9mm.

Retainer has a top head diameter of 15mm, a middle head diameter of 16mm, and a bottom head diameter of 21mm. The stem diameter is 10mm.

Retainer has a top head diameter of 13mm, a middle head diameter of 13mm, and a bottom head diameter of 16mm. The stem diameter is 9.5mm.

Retainer fasteners have a head size of 8mm, a stem diameter of 5.3mm, and a stem length of 7mm, and they are made of black nylon.

Retainer fasteners have a head size of 25mm x 30mm, a stem length of 15mm, and an overall length of 35mm, and they are specified as a bumper cover cap with sealer.

Retainer fasteners have a top head diameter of 13mm, a bottom head of 17.5mm, a stem diameter of 10.5mm, and a stem length of 15mm.

Bumper cover pins have a head diameter of 10mm, a stem length of 24mm, and they are made of black nylon.

Retainer fasteners have a top head diameter of 14mm, a bottom head of 18mm, a stem diameter of 12mm, and a stem length of 14mm.

Retaining clips have a head size of 8mm, a stem diameter of 5.7mm, a stem length of 7mm, and they are made of black nylon.

Retainer fasteners with sealer have a top head diameter of 12mm, a bottom head diameter of 16mm, a stem diameter of 8mm x 8mm, and a stem length of 14mm.

Retainer fasteners with sealer have a top head diameter of 13mm, a middle head diameter of 16mm, a bottom head diameter of 18mm, and a stem diameter of 6mm.

Retainer fasteners have a top head diameter of 18mm, a bottom head diameter of 18mm, a stem diameter of 5.9mm, and a stem length of 14mm.

Retainer fasteners have a top head diameter of 18mm, a bottom head diameter of 18mm, a stem diameter of 9mm, and a stem length of 13mm.

Retainer fasteners have a top head diameter of 13mm, a middle head diameter of 16mm, a bottom head diameter of 18mm, and a stem diameter of 8.5mm x 8mm.

Retainer fasteners have a top head diameter of 13mm, a middle head diameter of 16mm, a bottom head diameter of 18mm, and a stem diameter of 6mm.

Retainer fasteners have a head size of 30mm, a stem diameter of 6mm, a stem length of 13mm, and they are made of black nylon.

Retainer fasteners have a top head diameter of 13mm, a bottom head diameter of 15mm, a stem diameter of 9.5mm, and a stem length of 11mm.

Retainer fasteners have a top head diameter of 18mm, a bottom head diameter of 18mm, a stem diameter of 9.3mm, and a stem length of 13mm.

Retainer fasteners with sealer have a top head diameter of 13mm, a bottom head diameter of 15mm, a stem diameter of 9.5mm, and a stem length of 14mm.

Retaining clips have a head size of 8.3mm x 14.5mm, a stem diameter of 7mm, and a stem length of 16mm, and they are specified for the front hood cowl.

Retainer fasteners have a top head diameter of 13mm, a bottom head diameter of 18mm, a stem diameter of 9.5mm, and a stem length of 15mm.

Hood seal retainers have a head size of 13mm, a stem diameter of 7mm, a stem length of 10mm, and they are made of black nylon.

Cowl retainers have a top head diameter of 13mm x 18mm, a bottom head diameter of 18mm, a stem diameter of 10.7mm, and a stem length of 12mm.

Dash and fender apron retainers have a head size of 16mm, a stem diameter of 9mm, a stem length of 13mm, and they are made of black nylon.

Retainer fasteners have a top head diameter of 13mm, a middle head diameter of 17mm, a bottom head diameter of 13mm, and a stem diameter of 8mm.

Locking pin retainers have a head diameter of 15.7mm, an overall length of 27mm, a shoulder diameter of 8mm, and they are made of black nylon.

Retainer fasteners have a top head diameter of 18mm, a bottom head diameter of 19mm, a stem diameter of 9mm, and they are made of green and black nylon.

Interior trim retainers have a top head diameter of 13mm, a bottom head diameter of 18mm, a stem diameter of 9mm, and a stem length of 14mm.

Trim panel retainers have a top head diameter of 18mm, a bottom head diameter of 18mm, a stem diameter of 9mm, and a stem length of 14mm.

Trim panel retainers have a top head diameter of 12mm, a bottom head diameter of 18mm, a stem diameter of 10mm, and a stem length of 18mm.

Retainer fasteners have a top head diameter of 12mm, a bottom head diameter of 18mm, a stem diameter of 10mm, and a stem length of 16mm.

Retainer fasteners have a head size of 22mm and a stem length of 15mm, they are specified for the front fender, bumper, and engine, and they are made of black nylon.

Retainer fasteners have a top head diameter of 13mm, a bottom head diameter of 15mm, a stem diameter of 9mm, and a stem length of 11mm.

Retainer fasteners have a top head diameter of 13mm, a bottom head diameter of 17.5mm, a stem diameter of 9.5mm, and a stem length of 16mm.

Trim board retainers are specified for the front and rear door, and they have a top head diameter of 13mm, a stem diameter of 8mm, and a stem length of 14mm.

Moulding retainers with sealer have a top head diameter of 11mm x 15mm, a bottom head diameter of 18mm, a stem diameter of 9.7mm, and a stem length of 12mm.

Trim panel retainers with sealer have a top head diameter of 16mm, a bottom head diameter of 22mm, a stem diameter of 9mm, and a stem length of 15mm.

Door trim panel retainers with sealer have a head diameter of 13mm, a bottom head diameter of 18mm, a stem diameter of 8mm, and a stem length of 18mm.

Trim panel retainers with sealer have a top head diameter of 13mm, a bottom head diameter of 18mm, a stem diameter of 8mm x 8.5mm, and a stem length of 15mm.

Door trim panel retainers with sealer have a top head diameter of 13mm, a bottom head diameter of 18mm, a stem diameter of 8mm, and a stem length of 15mm.

Top vent retainers with sealer have a top head diameter of 13mm, a bottom head diameter of 16mm, a stem diameter of 8mm, and a stem length of 13mm.

Tailgate moulding retainers with sealer have a head diameter of 13mm, an overall length of 20mm, and a flange of 25mm.

Rocker and fender retainers with sealer have a head diameter of 14mm and an overall length of 19mm, and they are specified for a trim thickness of 2.5mm.

Trim panel retainers with sealer have a top head diameter of 12mm x 16mm, a bottom head diameter of 18mm, a stem diameter of 5mm, and a stem length of 34mm.

Trim panel retainers with sealer have a top head diameter of 13mm, a bottom head diameter of 15mm, a stem diameter of 9.5mm, and a stem length of 11mm.

Trim panel retainers with sealer have a top head diameter of 13mm, a bottom head diameter of 15mm, a stem diameter of 9mm, and a stem length of 14mm.

Trim panel retainers with sealer have a top head diameter of 13mm, a bottom head diameter of 18mm, a stem diameter of 9mm, and a stem length of 14mm.

Door panel retainers with sealer are specified for an 8.5mm hole, and they have a top head diameter of 13mm, a bottom head diameter of 18mm, and an overall length of 20mm.

Trim panel retainers with sealer have a top head diameter of 13mm x 16mm, a middle head diameter of 18mm, a bottom head diameter of 18mm, and a stem diameter of 6mm.

Trim panel and hood insulation retainers have a head size of 25mm, a stem diameter of 8mm, a stem length of 27mm, and they are made of black nylon.

Door trim panel retainers have a top head diameter of 15mm, a bottom head diameter of 19mm, a stem diameter of 9mm, and a stem length of 18mm.

Bumper fascia retainers have a head size of 22mm, a stem diameter of 11mm, a stem length of 28mm, and they are made of black nylon.

Interior trim panel clips have a head diameter of 2-3/4, a stem diameter of 3/4, a stem length of 2, and they are made of black nylon.

Hood insulation and fender shield retainers have a head diameter of 2-5/16, a stem diameter of 3/4, a stem length of 2, and they are made of black nylon.

Trim panel retainers have a top head diameter of 5/8, a bottom head diameter of 3/4, a stem diameter of 5/16, and a stem length of 1.

Panel retainer for dash panel attachment has a head size of 7/16, a stem diameter of 3/16, and a stem length of 5/8. The material is black nylon.

Panel retainer for fender and bumper shield attachment has a head diameter of 1-1/4, a stem diameter of 5/16, and a stem length of 5/8. The material is black nylon.

Panel retainer for trim panel attachment has a head size of 9/32, a stem diameter of 3/16, and a stem length of 1-7/16. The material is black nylon.

Panel retainer for screen shroud vent grille attachment has a head diameter of 7/32, a stem diameter of 3/32, and a stem length of 3/4. The material is black nylon.

Panel retainer for short end shield attachment has a head size of 7/16, a stem diameter of 3/16, and a stem length of 13/16. The material is black nylon.

Hood insulation retainer has a head size of 3/4, a stem diameter of 3/16, and a stem length of 3/4. The material is black nylon.

Hood insulation retainer has a head size of 8mm, a stem diameter of 7mm, and a stem length of 9mm. The material is black nylon.

Hood insulation retainer has a head size of 5.5mm, a stem diameter of 5.5mm, and a stem length of 9mm. The material is black nylon.

Panel retainer has a head size of 3/4, a stem diameter of 9/32, and a stem length of 1-1/2. The material is black nylon.

Panel retainer for dashboard attachment has a head size of 1-1/4, a stem diameter of 5/16, and a stem length of 1-5/16. The material is black nylon.

Panel retainer for door trim panel attachment has a top head diameter of 21/32, a bottom head diameter of 3/4, a stem diameter of 5/16, and a stem length of 3/4.

Panel retainer for door trim panel attachment has a top head diameter of 1/2, a bottom head diameter of 3/4, a stem diameter of 5/16, and a stem length of 5/8.

Panel retainer for trim panel attachment has a head size of 1-1/2, a stem diameter of 5/16, and a stem length of 1-3/4. The material is black nylon.

Panel retainer for rear header panel attachment has a top head diameter of 29/32, a bottom head diameter of 1-1/4, a stem diameter of 5/16, and a stem length of 1-1/16.

Panel retainer for trim panel attachment has a top head diameter of 18mm, a bottom head diameter of 20mm, a stem diameter of 6mm, and a stem length of 13mm.

Panel retainer for fascia to bumper attachment has a head size of 1, a stem diameter of 5/16, and a stem length of 1-7/16. The material is black nylon.

Panel retainer for door trim spacer attachment has a head size of 1-1/4, a stem diameter of 5/16, and a stem length of 5/16. The material is black nylon.

Panel retainer for rear hood seal attachment has a head diameter of 3/4, a stem diameter of 5/16, and a stem length of 1-3/8. The material is black nylon.

Panel retainer for hood seal attachment has a head size of 5/16, a stem diameter of 5/16, and a stem length of 2. The material is natural nylon.

Panel retainer for door trim panel attachment has a head size of 7/16, a stem diameter of 3/16, and a stem length of 1-1/2. The material is black nylon.

Panel retainer for trim panel attachment has a top head diameter of 15mm, a bottom head diameter of 17mm, a stem diameter of 6mm, and a stem length of 14mm.

Panel retainer for shield attachment has a head size of 1-1/16, a stem diameter of 5/16, and a stem length of 1. The material is black nylon.

Hood insulation retainer fits 1/4 and 6.4mm. Hood insulation retainer has a head size of 1-1/2 x 1-1/2 and a stem length of 1. The material is black nylon.

Panel retainer for trim panel attachment has a head size of 1-1/16, a stem diameter of 5/16, and a stem length of 13/16. The material is black nylon.

Hood insulation retainer has a head size of 1-1/4, a stem diameter of 5/16, and a stem length of 3/4. The material is black nylon.

Hood insulation retainer has a head size of 2, a stem diameter of 5/16, and a stem length of 1. The material is black nylon.

Panel retainer for fascia attachment has a head size of 2-5/8, a stem diameter of 7.5mm, and a stem length of 7.5mm. The material is black nylon.

Panel retainer for door trim panel attachment has a top head diameter of 29/32, a bottom head diameter of 1-5/16, a stem diameter of 5/16, and a stem length of 1-1/16.

Panel retainer for trim panel attachment has a top head diameter of 3/4, a bottom head diameter of 1-1/16, a stem diameter of 3/16, and a stem length of 13/16.

Panel retainer for door trim panel attachment has a top head diameter of 29/32, a bottom head diameter of 1-5/16, a stem diameter of 5/16, and a stem length of 1-1/16.

Hood insulation retainer has a head size of 1-1/2, a stem diameter of 5/16, and a stem length of 1-1/2. The material is black nylon.

Hood insulation retainer has a head size of 1-1/2, a stem diameter of 5/16, and a stem length of 1-5/16. The material is black polypropylene.

Panel retainer has a top head diameter of 15/32, a bottom head diameter of 25/32, a stem diameter of 5/16, and a stem length of 5/8.

Panel retainer has a top head diameter of 29/32, a bottom head diameter of 1-5/16, a stem diameter of 5/16, and a stem length of 15/16.

Panel retainer for radiator apron panel attachment has a head size of 1, a stem diameter of 7/16, and a stem length of 13/16. The material is black nylon.

Rubber rivet fastener has a head size of 1-1/2, a stem diameter of 3/8, and a stem length of 1-7/16. The material is black nylon.

Panel retainer for door trim panel attachment has a top head diameter of 29/32, a bottom head diameter of 3/4 x 7/32, a stem diameter of 5/16, and a stem length of 3/4.

Panel retainer for door frame spacer attachment has a head size of 1, a stem diameter of 5/16, and a stem length of 1-3/16. The material is black nylon.

Panel retainer for trim panel attachment has a head size of 3/4, a stem diameter of 11/32, and a stem length of 7/8. The material is black nylon. The application is sliding door and lift gate.

Panel retainer for trim panel attachment has a head size of 5/8, a stem diameter of 3/8, and a stem length of 3/4. The material is black nylon.

Panel retainer for carpet and shield attachment has a head size of 1, a stem diameter of 1/4, and a stem length of 25/32. The material is black nylon.

Panel retainer for headlight mounting shield attachment has a head size of 1, a stem diameter of 19/64, and a stem length of 1-11/16. The material is black nylon.

Panel retainer for trim panel attachment has a head size of 16mm, a stem diameter of 5mm, and a stem length of 13mm. The application is luggage compartment.

Mud flap retainer fits 6.3mm hole. Mud flap retainer has a head diameter of 18mm.

Hood insulation retainer has a head size of 25mm, a stem diameter of 9mm, and a stem length of 10mm. The material is black nylon.

Hood insulation retainer has a head size of 25mm, a stem diameter of 9mm, and a stem length of 10mm. The material is black nylon.

Panel retainer for bumper fascia attachment has a head size of 25mm, a stem diameter of 13mm, and a stem length of 15mm. The material is black nylon.

Panel retainer for rear bumper cover attachment has a head size of 25mm, a stem diameter of 7.5mm, and a stem length of 25mm. The material is black nylon.

Hood insulation retainer fits 6.35 hole. Hood insulation retainer has a head diameter of 19mm, a stem diameter of 7.5mm, and a stem length of 7mm. The material is black nylon.

Hood insulation retainer has a top head diameter of 25mm, a stem diameter of 5/16, and a stem length of 13/16.

Panel retainer for fender apron and radiator attachment has a head size of 1, a stem diameter of 11/32, and a stem length of 3/4. The material is black nylon.

Hood insulation retainer has a head size of 50mm, a stem diameter of 15mm x 18mm, and a stem length of 10mm. The material is black nylon.

Flange clip retainer is specified with a head size of 19/64, a stem diameter of 6.5mm x 7/32, and a stem length of 19/64. Flange clip retainer includes a stud sized 1/4-20 x 17/32. OE fitment is 6503336.

Trim panel retainer is specified with a head size of 23/32, a stem diameter of 3/8, and a stem length of 3/4. Trim panel retainer is made of black nylon. OE fitment is 4717224.

Trim panel retainer is specified with a head size of 5/8, a stem diameter of 1/4, and a stem length of 3/4. Trim panel retainer is made of black nylon. OE fitment is 6501948.

Bumper cover retainer is specified with a head size of 13/32, a stem diameter of 5/16, and a post length of 15/16. Bumper cover retainer is made of black nylon. OE fitment is 8509304-S100.

Trim panel retainer is specified with a head size of 7/32, a stem diameter of 3/8, and a stem length of 1. Trim panel retainer is made of black nylon. OE fitment is 889194-S100.

Bumper fascia retainer is specified with a head size of 25mm, a stem diameter of 13mm, and a stem length of 15mm. Bumper fascia retainer is made of black nylon. OE fitment is 6505684A and 6506293AA.

Trim panel retainer is specified with a head size of 18mm, a stem diameter of 8mm, and a stem length of 23mm. Trim panel retainer is made of black nylon. OE fitment is 6509590-AA.

Trunk trim and insulation retainer is specified with a head size of 23mm, a stem diameter of 8mm, and a stem length of 23mm. Trunk trim and insulation retainer is made of black nylon. OE fitment is 6508727-AA.

Retainer is specified with a head size of 20mm, a stem diameter of 8mm, and a stem length of 23mm. Retainer is made of black nylon. OE fitment is 14592087.

Retainer is specified with a head size of 20mm, a stem diameter of 8mm, and a stem length of 23mm. Retainer is made of gray nylon. OE fitment is 14592086.

Hood insulation retainer is specified with a head size of 28mm x 30mm, a stem length of 14mm, and an overall height of 16mm. Hood insulation retainer is made of black nylon. OE fitment is W708698-S300.

Retainer is specified with a head size of 20mm, a stem diameter of 7mm, and a stem length of 15mm. Retainer is made of black nylon. OE fitment is 5R3Z-5431012-BAA.

Retainer is specified with a head size of 31mm, a stem diameter of 7.6mm, and a stem length of 13mm. Retainer is made of black nylon. OE fitment is W706833-S300.

Retainer is specified with a head size of 20mm, a stem diameter of 9mm, and a stem length of 17mm. Retainer is made of black nylon. OE fitment is W715926-S300.

Retainer is specified with a head size of 26mm, a stem diameter of 7.5mm, and a stem length of 28mm. Retainer is made of black nylon. OE fitment is W706635-SSW.

Headlight retainer is specified with a head size of 25mm, a stem diameter of 8mm, and a stem length of 50mm. Headlight retainer is made of opt gray nylon. OE fitment is 25822063.

Fender and headliner retainer is specified with a head size of 25.4mm, a stem diameter of 8mm, and a stem length of 27mm. Fender and headliner retainer is made of black nylon. OE fitment is 15082005.

Retainer is specified with a head size of 20mm, a stem diameter of 8mm, and a stem length of 17mm. Retainer is made of black nylon. OE fitment is 15989431.

Retainer is specified with a head size of 20mm, a stem diameter of 7.8mm, and a stem length of 15mm. Retainer is made of black nylon. OE fitment is 11571159.

Retainer is specified with a head size of 25mm, a stem diameter of 5.8mm, and a stem length of 25.5mm. Retainer is made of black nylon. OE fitment is 11610747.

Retainer is specified with a head size of 33mm, a stem diameter of 8mm, and a stem length of 41mm. Retainer is made of light gray nylon. OE fitment is 89026634.

Hood insulation retainer is specified with a head size of 45mm, a stem diameter of 9.5mm, and a stem length of 20mm. Hood insulation retainer is made of tan nylon. OE fitment is 25749564.

Headliner retainer is specified with a head size of 25mm, a stem diameter of 8.5mm, and a stem length of 37mm. Headliner retainer is made of tan nylon. OE fitment is 10444839.

Headliner retainer is specified with a head size of 25mm, a stem diameter of 7.5mm, and a stem length of 22mm. Headliner retainer is made of tan nylon. OE fitment is 15944588.

Retainer is specified with a head size of 33mm, a stem diameter of 8mm, and a stem length of 41mm. Retainer is made of tan nylon. OE fitment is 89026635.

Trim panel retainer is specified with a top head diameter of 15mm, a bottom head diameter of 18mm, a stem diameter of 8mm, and a stem length of 14mm. Trim panel retainer is made of white nylon. OE fitment is 11561499.

Trim panel retainer is specified with a top head diameter of 16.5mm, a bottom head diameter of 18mm, a stem diameter of 9mm, and a stem length of 15mm. Trim panel retainer is made of white nylon. OE fitment is 11569700.

Retainer is specified with a head size of 10mm, a stem diameter of 5.5mm, and a stem length of 7mm. Retainer is made of black nylon. OE fitment is 91567-SAM-000.

Trunk lid and interior trim retainer is specified with a head size of 28mm, a stem diameter of 7mm, and a stem length of 13mm. Trunk lid and interior trim retainer is made of black nylon. OE fitment is 90671-S00-003ZK.

Hood insulation retainer is specified with a head size of 30mm, a stem diameter of 15mm x 21mm, and a stem length of 14mm. Hood insulation retainer is made of black nylon. OE fitment is 91501-SWA-003.

Retainer is specified with a head size of 13mm, a stem diameter of 5mm, and a stem length of 11mm. Retainer is made of black nylon. OE fitment is 86438-A4100.

Retainer is specified with a head size of 18mm x 16mm, a stem diameter of 8mm, and a stem length of 14mm. Retainer is made of black nylon. OE fitment is 86434-A4000.

Retainer is specified with a head size of 18mm, a stem diameter of 8mm, and a stem length of 16mm. Retainer is made of gray nylon. OE fitment is 85746-06000LX.

Retainer is specified with a head size of 18mm, a stem diameter of 6mm, and a stem length of 16mm. Retainer is made of tan nylon. OE fitment is 85746-06000RU.

Retainer is specified with a head size of 18mm, a stem diameter of 6mm, and a stem length of 17mm. Retainer is made of tan nylon. OE fitment is MC99134.

Bumper retainer is specified with a head size of 17mm, a stem diameter of 4.7mm x 4.7mm, and a stem length of 12mm. OE fitment is 90467-05125.

Retainer is specified with a head size of 16mm, a stem diameter of 6.5mm, and a stem length of 14mm. Retainer is made of black nylon. OE fitment is B003-68-865-00.

Retainer is specified with a head size of 20mm, a stem diameter of 7mm, and a stem length of 10mm. Retainer is made of black nylon. OE fitment is TD11-56-694.

Hood insulation retainer is specified with a head size of 26mm, a stem diameter of 8mm, and a stem length of 10mm. Hood insulation retainer is made of black nylon. OE fitment is 65846-42000.

Bumper and trim retainer is specified with a head size of 12mm, a stem diameter of 6mm, and a stem length of 15mm. Bumper and trim retainer is made of black nylon. OE fitment is 01553-01A50.

Retainer is specified with a head size of 21mm, a stem diameter of 7.5mm, and a stem length of 23mm. Retainer is made of black nylon. OE fitment is 6983.17.

Retainer is specified with a head size of 10mm, a stem diameter of 8mm, and a stem length of 15mm. Retainer is an internal trim retainer. OE fitment is 6989.21.

Retainer is specified with a head size of 13mm, a stem diameter of 7mm, and a stem length of 13mm. Retainer is made of black nylon. OE fitment is 77-03-077-030.

Retainer is specified with a head size of 15mm, a stem diameter of 8mm, and a stem length of 17mm. Retainer is made of black nylon. OE fitment is 77-03-077-231.

Retainer is specified with a head size of 25mm, a stem diameter of 10mm x 10.5mm, and a stem length of 35mm. Retainer is made of black nylon. OE fitment is 77-03-077-435.

Retainer is specified with a head size of 18mm, a stem diameter of 10mm, and a stem length of 22mm. Retainer is made of black nylon. OE fitment is 77-03-077-225.

Retainer is specified with a head size of 17mm, a stem diameter of 7mm, and a stem length of 17mm. Retainer is made of white nylon.

Hood insulation retainer is specified with a head size of 30mm, a stem diameter of 7mm, and a stem length of 30mm. Hood insulation retainer is made of black nylon. OE fitment is 90913-0074.

Trim panel retainer is specified with a head size of 17mm, a stem diameter of 7mm, and a stem length of 15mm. Trim panel retainer is made of black nylon. OE fitment is 99045-AE093AMA.

Retainer is specified with a head size of 20mm, a stem diameter of 6mm, and a stem length of 22mm. Retainer is made of black nylon. OE fitment is 95202-AC400ML.

Hood insulation retainer is specified with a head size of 24mm, a stem diameter of 6.2mm, and a stem length of 18mm. Hood insulation retainer is made of black nylon. OE fitment is 90409-06039-5ES.

Headliner retainer clips have a head size of 20mm, a stem diameter of 6mm, and a stem length of 15mm. The material is tan nylon.

Door and roof rail retainer clips have a head size of 35mm, a stem diameter of 9mm, and a stem length of 8mm. The material is black nylon.

Fender seal retainer clips have a head size of 8mm and a stem diameter of 8mm. The material is black nylon.

Headliner retainer clips have a head size of 20mm, a stem diameter of 6mm, and a stem length of 15mm. The material is gray nylon.

Panel retainer clips have a stem diameter of 23mm and a stem length of 16mm. The application is radiator grille and scuff plate.

Panel retainer clips have a head size of 25mm, a stem diameter of 8mm, and a stem length of 23mm. The material is black nylon.

Trim panel retainer clips have a top head diameter of 12mm, a bottom head diameter of 12mm, a stem diameter of 5.9mm, and a stem length of 12mm.

Panel retainer clips have a head size of 12mm, a bottom head diameter of 12mm, a stem diameter of 10mm, and a stem length of 20mm.

Fender flare and bumper hole retainer clips fit a 6.3mm hole and have a head diameter of 22mm and an overall length of 37mm. The material is black nylon.

Door and interior trim panel retainer clips are specified for door and interior trim panel applications.

Push type retainer pins are specified as push type retainer pins.

Fascia rivet retainer clips fit a 1/2 (12.7mm) hole and have a head diameter of 25mm, a stem length of 1-3/4 (19mm), and a shoulder length of 3/4 (19mm).

Push type rivet retainer clips fit a 12.7mm hole and have a head diameter of 27mm (1-1/16) and a stem length of 5/32 (4mm). The color is blue.

Fascia rivet retainer clips fit a 1/2 (12.7mm) hole and have a head diameter of 27mm (1-1/16), a stem length of 7/8 (22mm), and a shoulder length of 1/4 (6.4mm).

Fascia rivet retainer clips fit a 3/8 (9.5mm) hole and have a head diameter of 29mm and a stem diameter of 7/32 (5.6mm). The material is black nylon.

Push type rivet retainer clips fit a 1/4 (6.4mm) hole and have a head diameter of 25mm (1) and a stem length of 1-1/8 (28.6mm). The application is front fender mud skirt and fender liner.

Push type rivet retainer clips fit a 7/16 (11.1mm) hole and have a head diameter of 40mm (1-9/16) and a stem length of 1-1/2 (38.1mm).

Push type retainer clips fit a 5/16 (7.9mm) hole and have a head diameter of 24mm (15/16) and a stem diameter of 6.4mm. The material is black nylon.

Push type retainer clips fit a 3/8 (9.5mm) hole and have a head diameter of 27mm (1-1/16) and a stem length of 1-1/4 (31.75mm). The material is black nylon.

Push type retainer clips fit a 3/8 (9.5mm) hole and have a head diameter of 27mm (1-1/16) and a stem length of 1-1/4 (31.75mm). The application is grille attachment.

Push type retainer clips fit a 1/4 (6.4mm) hole and have a head diameter of 27mm (1-1/16) and a stem diameter of 7/16 (11mm). The application is license plate and grille to headlight bracket.

Screw type retainer clips fit a 1/4 (6.4mm) hole and have a head diameter of 17/16 (17mm) and a stem diameter of 7/8 (22mm). The material is black nylon.

Push type retainer clips fit a 6.3mm hole and have a head diameter of 15mm, a stem diameter of 7mm, and a stem length of 27mm.

Push type retainer clips fit a 6.3mm hole and have a head diameter of 15mm and a stem length of 13mm. The application is front fender skirt.

Push type retainer clips fit a 9mm hole and have a head diameter of 18mm and a stem length of 12mm. The application is bumper cover and wheel housing.

Push type retainer clips fit a 10mm hole and have a head diameter of 15mm and a stem length of 15mm. The application is bumper cover and grille.

Push type retainer clips fit a 6.3mm hole and have a head diameter of 6.4mm and a stem length of 13mm. The application is door trim panel.

Push type retainer clips fit a 8mm hole and have a head diameter of 18mm and a stem length of 14mm. The application is cowl panel.

Push type retainer clips fit a 6.3mm hole and have a head diameter of 18mm and a stem length of 10mm. The application is trim panel.

Push type retainer clips fit a 6.3mm hole and have a head diameter of 18mm and a stem length of 10mm. The application is trim panel.

Rear bumper cover push type retainer clips fit a 10mm hole and have a head diameter of 19mm and a stem length of 18mm.

Push type retainer clips fit a 6.3mm hole and have a head diameter of 18mm and a stem length of 23mm. The application is bumper cover.

Push type retainer clips have a head diameter of 18mm, a stem diameter of 8mm, and a stem length of 18mm. The materials are black nylon and Santoprene.

Push type rivet retainer clips fit a 1/4 (6.4mm) hole and have a head diameter of 13mm, a stem diameter of 7mm, and a stem length of 34mm. The application is wheel opening moulding.

Push type retainer clips fit a 6.3mm hole and have a head diameter of 17mm and a stem length of 16mm. The application is tailgate lining.

Push type retainer clips have a head diameter of 16mm and a stem length of 9mm. The application is cowl panel and luggage compartment.

Push-to-release retainer clips fit a 6.3mm hole and have a flange diameter of 18mm and a stem length of 9mm. The application is door panel.

Push type retainer clips fit a 6.3mm hole and have a head diameter of 20mm and a stem length of 22mm.

Push type rivet retainer clips fit a 6.3mm hole and have a head diameter of 20mm and a stem length of 17mm. The application is radiator shield.

Push type retainer clips fit a 6.3mm hole and have a head diameter of 18mm and a stem length of 22mm. The application is bumper fascia.

Push type retainer clips fit a 6.3mm hole and have a head diameter of 18mm and a stem length of 10mm. The application is front bumper.

Push type retainer clips fit a 6.3mm hole and have a head diameter of 15mm and a stem length of 11mm. The application is door trim panel.

Push type retainer clips fit a 6.3mm hole and have a head diameter of 15mm and a stem length of 17mm. The material is black nylon.

Push type retainer clips fit a 6.3mm hole and have a head diameter of 20mm and a stem length of 19mm. The material is black nylon.

Push type retainer clips fit a 6.3mm hole and have a head diameter of 20mm and a stem length of 19mm. The material is black nylon.

Push type retainer clips fit a 10mm hole and have a head diameter of 20mm and a stem length of 13mm. The application is front bumper.

Push type retainer clips fit a 10mm hole and have a head diameter of 20mm and a stem length of 14mm.

Push type retainer clips fit a 6.3mm hole and have a head diameter of 15mm and a stem length of 15mm. The material is black nylon.

Push type retainer clips fit a 6.3mm hole and have a head diameter of 10mm and a stem length of 9mm. The application is bumper fascia.

Push type retainer clips fit a 6.3mm hole and have a head diameter of 9mm and a stem length of 7mm. The application is trunk compartment.

Push type retainer clips fit a 6.3mm hole and have a head diameter of 12mm and a stem length of 10mm. The applications are rocker panel, air duct compartment, and wheel housing.

Panel retainer clips have a head diameter of 20mm, a stem diameter of 7mm, and a stem length of 17mm. The application is rocker trim wheel housing.

Push type retainer clips fit a 10mm hole and have a head diameter of 20mm and a stem length of 23mm. The material is black nylon.

Push type retainer clips fit a 11mm hole and have a head diameter of 24mm and a stem length of 20mm. The shoulder length is 3mm.

Push type retainer clips fit a 9mm hole and have a head diameter of 22mm and a stem length of 10mm. The material is gray nylon.

Push type retainer with sealer fits a 9 mm hole, has a head diameter of 22 mm, has a stem diameter of 22 mm, has a stem length of 16 mm, and is made of black nylon.

Push type retainer fits an 8 mm hole, has a head diameter of 20 mm, has a stem length of 10 mm, and is made of black nylon.

Push type retainer fits a 7 mm hole, has a head diameter of 16 mm, has a stem length of 14 mm, and is made of gray nylon.

Push type retainer fits a 7 mm hole, has a head diameter of 15 mm, has a stem length of 10 mm, and is made of black nylon.

Push type retainer fits an 8 mm hole, has a head diameter of 13 mm, has a stem length of 13 mm, and is made of black nylon.

Push type retainer fits an 8 mm hole, has a head diameter of 18 mm, has a stem length of 10 mm, and is made of black nylon.

Push type retainer fits a 7 mm hole, has a head diameter of 18 mm, has a stem length of 12 mm, and is used on a lower radiator shield.

Push type retainer fits a 7 mm hole, has a head diameter of 25 mm, has a stem length of 25 mm, and is made of black nylon.

Push type retainer fits an 11 mm hole, has a head diameter of 25 mm, has a stem length of 35 mm, and is made of natural nylon.

Push type retainer fits a 6 mm hole, has a head diameter of 12 mm, has a stem length of 12 mm, and is made of black nylon.

Push type retainer fits a 6.5 mm hole, has a head diameter of 18 mm, has a stem length of 18 mm, and is made of black nylon.

Push type retainer fits a 6.3 mm hole, has a head diameter of 18 mm, has a stem length of 20 mm, and is made of black nylon.

Push type retainer has an outside diameter of 24 mm, has a stem diameter of 8 mm, has a stud size of 4.8 mm, is specified for fender, quarter panel, and grille applications, and has a zinc finish.

Push type retainer fits a 6 mm hole, has a head diameter of 16 mm, has a stem length of 22 mm, and is made of black nylon.

Push type retainer fits a 6 mm hole, has a head size of 14 mm x 21 mm, has a stem length of 16 mm, is specified for front and rear bumper fascia applications, and is made of black nylon.

Push type retainer fits a 6 mm hole, has a head diameter of 21 mm, has a stem length of 12 mm, and is made of black nylon.

Push type retainer fits a 10 mm hole, has a head diameter of 20 mm, has a stem length of 13 mm, and is made of black nylon.

Push type retainer fits a 7 mm hole, has a head diameter of 19 mm, has a stem length of 11 mm, and is made of black nylon.

Push type retainer fits a 5.5 mm hole, has a head diameter of 19 mm, has a stem length of 13 mm, and is made of black nylon.

Push type retainer fits a 5.5 mm hole, has a head diameter of 19 mm, has a stem length of 13 mm, and is made of black nylon.

Push type retainer fits a 10 mm hole, has a head diameter of 20 mm, has a stem length of 22 mm, is specified for front bumper applications, and is made of black nylon.

Push type retainer fits a 13 mm hole, has a head diameter of 22 mm, has a stem length of 24 mm, is specified for front fender panel applications, and is made of black nylon.

Push type retainer fits a 7 mm hole, has a head diameter of 19 mm, has a stem length of 11 mm, and is made of black nylon.

Push type retainer fits a 5.5 mm hole, has a head diameter of 19 mm, has a stem length of 10 mm, and is made of black nylon.

Push type retainer fits an 8 mm hole, has a head diameter of 13 mm, has a stem length of 13 mm, and is made of black nylon.

Push type retainer fits a 6 mm hole, has a head diameter of 18 mm, has a stem length of 13 mm, and is made of black nylon.

Push type retainer fits a 6 mm hole, has a head diameter of 11 mm, has a stem length of 12 mm, and is made of black nylon.

Push type retainer fits a 6 mm hole, has a head diameter of 12 mm, has a stem length of 9 mm, and is made of black nylon.

Push type retainer fits an 8 mm hole, has a head diameter of 15 mm, has a stem length of 11 mm, and is made of black nylon.

Push type retainer fits a 6 mm hole, has a head diameter of 12 mm, has a stem length of 12 mm, and is made of black nylon.

Push type retainer fits an 8 mm hole, has a head diameter of 20 mm, has a stem length of 15 mm, and is made of black nylon.

Push type retainer fits a 5 mm hole, has a head diameter of 15 mm, has a stem length of 14 mm, and is made of black nylon.

Push type retainer fits an 8 mm hole, has a head diameter of 20 mm, has a stem length of 20 mm, and is made of black nylon.

Retainer fits an 8 mm hole, has a head diameter of 23 mm, has a stem length of 12 mm, and has a rectangular head measuring 9 mm x 20 mm.

Retainer fits an 8 mm hole, has a head diameter of 20 mm, has a stem length of 10 mm, and is made of black nylon.

Retainer fits a 6.3 mm hole, has a head diameter of 22 mm, has a stem length of 14 mm, and is made of black nylon.

Push type retainer fits an 8 mm hole, has a head diameter of 18 mm, has a stem length of 14 mm, and is made of black nylon.

Push type retainer fits a 10 mm hole, has a head diameter of 21 mm, has a stem length of 15 mm, and is made of black nylon.

Push type retainer fits a 7 mm hole, has a head diameter of 20 mm, has a stem length of 11 mm, and is made of black nylon.

Push type retainer fits a 7 mm hole, has a head diameter of 20 mm, has a stem length of 12 mm, and is made of black nylon.

Push type retainer fits an 11 mm hole, has a head diameter of 25 mm, has a stem length of 25 mm, has a shoulder length of 3 mm, and is made of black nylon.

Push type retainer fits an 8 mm hole, has a head diameter of 18 mm, has a stem length of 18 mm, and is made of black nylon.

Push type retainer fits an 11 mm hole, has a head diameter of 20 mm, has a stem length of 12 mm, and is made of black nylon.

Push type retainer fits a 7 mm hole, has a head diameter of 16 mm, has a stem length of 13 mm, and is made of black nylon.

Push type retainer fits a 7 mm hole, has a head diameter of 16 mm, has a stem length of 13 mm, and is made of black nylon.

Push type retainer fits an 11 mm hole, has a head diameter of 14 mm, has a stem length of 14 mm, and is made of black nylon.

Push type retainer fits a 6 mm hole, has a head diameter of 16 mm, has a stem length of 11 mm, and is made of black nylon.

Push type retainer fits an 8 mm hole, has a head diameter of 20 mm, has a stem length of 10 mm, and is made of black nylon.

Push type retainer fits a 10 mm hole, has a head diameter of 22 mm, has a stem length of 22 mm, and is made of black nylon.

Push type retainer fits a 7 mm hole, has a head diameter of 21 mm, has a stem length of 12 mm, and is made of black nylon.

Push type retainer fits a 4 mm hole, has a head diameter of 9 mm, has a stem length of 7 mm, and is made of black nylon.

Push type retainer fits an 8 mm hole, has a head diameter of 21 mm, has a stem length of 10 mm, and is made of black nylon.

Push type retainer fits a 7 mm hole, has a head diameter of 18 mm, has a stem length of 18 mm, and is made of black nylon.

Push type retainer fits a 7 mm hole, has a head diameter of 20 mm, has a stem length of 11 mm, and is made of black nylon.

Push type retainer fits an 8 mm hole, has a head diameter of 25 mm, has a stem length of 21 mm, has a bottom head diameter of 26 mm, and is made of black nylon.

Push type retainer fits an 11 mm hole, has a head diameter of 25 mm, has a stem length of 25 mm, and is made of black nylon.

Push type retainer products fit a 7 mm hole and have a 20 mm head diameter with a 20 mm stem length. Push type retainer products are specified for radiator splash shield applications and reference OEM manufacturer designation 90467-07214.

Push type retainer products fit a 7 mm hole and have a 16 mm head diameter with a 14 mm stem length. Push type retainer products are made of black nylon and reference OEM manufacturer designation 90080-46294.

Push type retainer products fit a 9 mm hole and have a 22 mm head diameter with a 25 mm stem length. Push type retainer products are specified for bumper and engine under cover applications and reference OEM manufacturer designation 90467-09227.

Push type retainer products fit an 8 mm hole and have a 20 mm head diameter with a 17 mm stem length. Push type retainer products are made of black nylon and reference OEM manufacturer designation 75887-06030.

Push type retainer products fit a 7 mm hole and have an 18 mm head diameter with an 18 mm stem length. Push type retainer products are made of black nylon and reference OEM manufacturer designation 53888-48010.

Push type retainer products fit a 9 mm hole and have an 18 mm head diameter with an 18 mm stem length. Push type retainer products are specified for front spoiler and grille applications and reference OEM manufacturer designation 90467-09185.

Push type retainer products fit an 8 mm hole and have an 18 mm head diameter with a 16 mm stem length. Push type retainer products are made of black nylon and reference OEM manufacturer designation 90467-10206.

Push type retainer products fit a 7 mm hole and have a 9 mm head diameter with a 9 mm stem length. Push type retainer products are specified for bumper cover applications and reference OEM manufacturer designation 90467-07071-22.

Cowl retainer products have a 22 mm top head diameter and a 16 mm bottom head diameter with a 4 mm stem diameter and a 6.5 mm stem length. Cowl retainer products reference OEM manufacturer designation 90602-S2A-003.

Cowl and grille retainer clip products have an 11 mm head size with a 4.5 mm stem diameter and a 15 mm stem length. Cowl and grille retainer clip products are specified for cowl grille applications and reference OEM manufacturer designation 68220-61100.

Push type retainer products fit an 8 mm hole and have a 12 mm head diameter with an 11 mm stem length. Push type retainer products are made of dark gray nylon and reference OEM manufacturer designation N9038-550-1.

Push type retainer products fit an 8 mm square hole and have a 26 mm head diameter with a 15 mm stem length. Push type retainer products are made of black nylon and reference OEM manufacturer designation 1H0-819-055-C01C.

Push type retainer products fit an 8 mm square hole and have a 20 mm head diameter with a 13 mm stem length. Push type retainer products are made of black nylon and reference OEM manufacturer designation 1H0-867-199-A.

Push type retainer products fit an 8 mm hole and have a 16 mm head diameter with an 11 mm stem length. Push type retainer products are made of gray nylon and reference OEM manufacturer designation 701-867-299.

Push type retainer products have a 30 mm outside diameter and use a 5 mm stud size. Push type retainer products are specified for radiator support and splash shield applications and reference OEM manufacturer designations N90-33-506, N90-796-502, and 441-863-987-3.

Push type retainer products have a 30 mm outside diameter and use a 5 mm stud size. Push type retainer products are specified for splash shield and wheel well applications, are made of black nylon, and reference OEM manufacturer designation N90-33-506.

Push type retainer products fit an 8.5 mm hole and have a 14 mm head diameter with a 10 mm stem length. Push type retainer products are made of black nylon and reference OEM manufacturer designation 3933-867-633-4FB.

Push type retainer products fit an 8 mm hole and have a 25 mm head diameter with an 8 mm stem length. Push type retainer products are made of black and white nylon and reference OEM manufacturer designation N9068-243.

Push type retainer products fit a 9/32 (7.2 mm) hole and have a 17 mm head diameter with a 1-7/32 (31 mm) stem length. Push type retainer products are made of natural nylon and reference OEM manufacturer designation 90467-07272.

Trim panel retainer products have a 13 mm top head diameter and a 13 mm bottom head diameter with a 5.5 mm stem diameter and a 14 mm stem length. Trim panel retainer products reference OEM manufacturer designation 59015-14K00.

Trim panel retainer products have a 13 mm top head diameter and a 13 mm bottom head diameter with a 5.5 mm stem diameter and a 14 mm stem length. Trim panel retainer products reference OEM manufacturer designation 59015-14K00.

Trim panel retainer products have a 13 mm top head diameter and a 13 mm bottom head diameter with a 5.5 mm stem diameter and a 14 mm stem length. Trim panel retainer products reference OEM manufacturer designation 59015-14K00.

Trim panel retainer products have a 13 mm top head diameter, a 16 mm middle head diameter, and an 18 mm bottom head diameter with a 5 mm stem diameter and a 9 mm stem length. Trim panel retainer products reference OEM manufacturer designation 94078-FA080.

Trim panel retainer products have a 28.5 mm head size with a 5 mm stem diameter and an 11 mm stem length. Trim panel retainer products are made of tan and white nylon and reference OEM manufacturer designation 1H0-868-243-B.

Trim panel retainer products have a 16 mm top head diameter and an 18 mm bottom head diameter with a 10 mm stem diameter and a 14 mm stem length. Trim panel retainer products reference OEM manufacturer designation 6998-243-C.

Trim panel retainer products have a 22 mm top head diameter and a 20 mm bottom head diameter with an 11 mm stem diameter and an 11 mm stem length. Trim panel retainer products reference OEM manufacturer designation 6K6-868-243-C.

Weatherstrip retainer products have a 7 mm x 16 mm head size with a 7 mm stem diameter and a 10 mm stem length. Weatherstrip retainer products are made of white nylon and reference OEM manufacturer designations N8032-6500, 80833-8500, and 90664-671-003.

Weatherstrip retainer products have a 10 mm head size with a 6 mm stem diameter and a 12 mm stem length. Weatherstrip retainer products are made of black nylon and reference OEM manufacturer designations 85022328 and 20699808.

Weatherstrip retainer products have a 3/8 head size with a 3/16 stem diameter and a 7/16 stem length. Weatherstrip retainer products are made of black nylon and reference OEM manufacturer designation 4876498.

Weatherstrip retainer products have a 7/32 head size with a 3/16 stem diameter and a 5/8 stem length. Weatherstrip retainer products are made of black nylon and reference OEM manufacturer designation 4658673.

Weatherstrip retainer products have a 7/16 head size with a 3/16 stem diameter and a 5/16 stem length. Weatherstrip retainer products are made of black nylon and reference OEM manufacturer designation 10169777.

Weatherstrip retainer products have a 3/8 head size with a 3/16 stem diameter and a 3/8 stem length. Weatherstrip retainer products are made of black nylon and reference OEM manufacturer designation 2964547.

Weatherstrip retainer products have a 3/8 head size with a 3/16 stem diameter and a 21/32 stem length. Weatherstrip retainer products are made of natural nylon and reference OEM manufacturer designation 385677.

Weatherstrip retainer products have a 6 mm head size with a 5 mm stem diameter and a 10 mm stem length. Weatherstrip retainer products are made of red nylon and reference OEM manufacturer designation 91530-SP1-003.

Weatherstrip retainer products have a 6 mm head size with a 5 mm stem diameter and a 10 mm stem length. Weatherstrip retainer products are made of natural nylon and reference OEM manufacturer designation 91530-ST5-003.

Weatherstrip retainer products have a 5 mm x 15 mm head size with a 5 mm stem diameter and an 8 mm stem length. Weatherstrip retainer products are made of natural nylon and reference OEM manufacturer designation N806340-S.

Weatherstrip retainer products have a 5 mm x 15 mm head size with a 6 mm stem diameter and a 10 mm stem length. Weatherstrip retainer products are made of natural nylon and reference OEM manufacturer designations 67867-0C010, 67867-12150, and 67868-02020.

Weatherstrip retainer products have a 10 mm head size with a 9 mm stem diameter and a 14.5 mm stem length. Weatherstrip retainer products are made of yellow nylon.

Weatherstrip retainer products have a 5 mm x 14 mm head diameter with a 6.5 mm stem diameter and a 10 mm stem length. Weatherstrip retainer products are made of blue nylon.

Weatherstrip retainer products have a 1/4 x 2/32 head size with a 15/32 stem length. Weatherstrip retainer products are made of white nylon and reference OEM manufacturer designations 4696129 and 21077575.

Weatherstrip retainer products have a 6 mm head size with a 6 mm stem diameter and a 10 mm stem length. Weatherstrip retainer products are made of black nylon and reference OEM manufacturer designation 91567-SR2-013.

Weatherstrip retainer products have a 10 mm head size with a 6 mm stem diameter and an 8 mm stem length. Weatherstrip retainer products are made of black nylon and reference OEM manufacturer designation 01553-08961.

Weatherstrip retainer products have a 12 mm head size with a 6.5 mm stem diameter and an 11 mm stem length. Weatherstrip retainer products are made of black nylon and reference OEM manufacturer designation 90467-06128.

Weatherstrip retainer products have a 5 mm x 15 mm head size with a 7 mm stem diameter and a 17 mm stem length. Weatherstrip retainer products are made of black nylon and reference OEM manufacturer designation 1H0-837-719.

Retainer products have a 15 mm x 15 mm head size with a 31 mm overall length. Retainer products are specified for rear arch scuff plate applications, are made of black nylon, and reference OEM manufacturer designations 2J1-867-741 and A901-988-00-25.

Seat back panel retainer products have a 1/2 top head diameter and a 5/8 bottom head diameter with an 11/32 stem diameter and a 1-7/16 stem length. Seat back panel retainer products are made of black nylon and reference OEM manufacturer designation 387182-S.

Weatherstrip retainer products have a 4 mm head diameter with a 4 mm stem diameter and a 12 mm stem length. Weatherstrip retainer products are made of black nylon and reference OEM manufacturer designation N806289-S.

Weatherstrip retainer products have a 3/16 head diameter with a 5/8 stem length. Weatherstrip retainer products are made of black nylon and reference OEM manufacturer designations 20413107, 388246-S, and 4006516.

Shield retainer products are specified for battery post cable shield and engine splash shield applications and have an 11/16 head diameter with a 1-5/16 stem length. Shield retainer products are made of black nylon and reference OEM manufacturer designations 10121502, 6033082, 6033840, and 390018-S.

Trim panel retainer products fit a 7 mm hole and use a 4 mm screw size with a 10 mm width and a 10 mm length. Trim panel retainer products reference OEM manufacturer designation 90468-04030.

Bumper and grille mounting retainer products measure 13.1 mm W x 29.7 mm L. Bumper and grille mounting retainer products reference OEM manufacturer designation 86593-24000.

____________________________________________________________________________

Rivets & Rivet Tools 

Headlight retaining rivets have a rivet diameter of 1/4 inch (6.3 mm), a flange diameter of 13/32 inch, and a shoulder diameter of 13/32 inch, and feature a steel body and mandrel, specifications routinely encountered during headlamp assembly and replacement work performed by body shops serving Hillsdale, New York.

Bumper drive type rivets have a head diameter of 20 mm. Bumper drive type rivets have an unspecified head length. Bumper drive type rivets have a stem length of 16 mm. Bumper drive type rivets have a panel range of 8 mm.

Rear bumper screw type fasteners have a head diameter of 18 mm. Rear bumper screw type fasteners have a stem length of 18 mm. Rear bumper screw type fasteners have a panel range of 3.8 mm to 5 mm.

Drive type rivets fit a 7 mm hole. Drive type rivets have a head diameter of 20 mm. Drive type rivets have a stem length of 8 mm. Drive type rivets are used on the front fender liner.

Push-to-release drive type rivets fit a 7.5 mm hole. Push-to-release drive type rivets have a head diameter of 16 mm. Push-to-release drive type rivets have a stem length of 12 mm. Push-to-release drive type rivets are used on the liftgate upper window and lower garnish.

Drive type rivets fit a 7.5 mm hole. Drive type rivets have a head diameter of 18 mm. Drive type rivets have a stem length of 13 mm. Drive type rivets are used on the cowl vent.

Drive type rivets fit an 8 mm hole. Drive type rivets have a flange diameter of 10 mm. Drive type rivets have a panel range of 3 mm to 8 mm. Drive type rivets are used on the front bumper.

Drive type rivets fit a 9 mm hole. Drive type rivets have a head diameter of 25 mm. Drive type rivets have a stem length of 12 mm. Drive type rivets have a shoulder of 3 mm.

Drive type rivets have a head diameter of 20 mm. Drive type rivets have a stem length of 13 mm. Drive type rivets have a panel range of 2 mm to 6 mm. Drive type rivets are used on the front bumper and radiator.

Drive rivets have a head diameter of 10 mm. Drive rivets have a stem length of 14 mm. Drive rivets have an unspecified panel range. Drive rivets are used in the fender area.

Drive type rivets fit an 8 mm hole. Drive type rivets have a head diameter of 20 mm. Drive type rivets have a stem length of 28 mm. Drive type rivets are used on the bumper fascia.

Drive rivets fit a 6.5 mm hole. Drive rivets have a head diameter of 18 mm. Drive rivets have a stem length of 20 mm. Drive rivets are used on the air deflector, bumper fascia, and front brake caliper cooling duct.

Drive rivets fit an 8.5 mm hole. Drive rivets have a head diameter of 20 mm. Drive rivets have a stem length of 22 mm. Drive rivets are used on the cowl vent and fender.

Drive rivets have a head diameter of 18 mm. Drive rivets have a stem length of 20 mm. Drive rivets are used on the fender, wheel, and bumper.

Drive rivets have a head diameter of 18 mm. Drive rivets have a stem length of 17.5 mm. Drive rivets are used on the air distributor and windshield defrost.

Drive rivets have a head diameter of 18 mm. Drive rivets have a stem length of 22 mm. Drive rivets are used on the air dam and grille.

Drive rivets fit an 8 mm hole. Drive rivets have a head diameter of 19 mm. Drive rivets have a stem length of 18 mm. Drive rivets are used on the fascia and engine compartment.

Drive rivets fit an 8.5 mm hole. Drive rivets have a head diameter of 20 mm. Drive rivets have a stem length of 18 mm. Drive rivets are used on the bumper fascia, flares, and air dam.

Drive rivets fit an 8.5 mm hole. Drive rivets have a head diameter of 20 mm. Drive rivets have a stem length of 24 mm. Drive rivets are used on the bumper fascia, fender, and floor panel.

Drive rivets fit a 10.5 mm hole. Drive rivets have a head diameter of 25 mm. Drive rivets have a stem length of 20 mm. Drive rivets are used on the panel, fender, gas tank, and fender attachment.

Drive rivets fit a 10.5 mm hole. Drive rivets have a head diameter of 25 mm. Drive rivets have a stem length of 23 mm. Drive rivets are used for panel attachment and general purpose.

Bumper drive type rivets fit a 10 mm hole. Bumper drive type rivets have a stem length of 18 mm. Bumper drive type rivets have a panel range of 3 mm. Bumper drive type rivets have a flange diameter of 20 mm.

Hood insulator drive type rivets fit an 8 mm hole. Hood insulator drive type rivets have a head diameter of 29 mm. Hood insulator drive type rivets have a stem length of 9.5 mm. Hood insulator drive type rivets have a panel range of 5 mm.

Structural rivets have a rivet diameter of 3/16. Structural rivets have a grip range of .062 to .270. Structural rivets have an aluminum body. Structural rivets have an aluminum mandrel.

Structural rivets have a rivet diameter of 3/16. Structural rivets have a grip range of .214 to .420. Structural rivets have an aluminum body. Structural rivets have an aluminum mandrel.

Structural rivets have a rivet diameter of 3/16. Structural rivets have a grip range of .080 to .375. Structural rivets have an aluminum body. Structural rivets have an aluminum mandrel.

Structural rivets have a rivet diameter of 3/16. Structural rivets have a grip range of .062 to .270. Structural rivets have a steel body. Structural rivets have a steel mandrel.

Structural rivets have a rivet diameter of 3/16. Structural rivets have a grip range of .214 to .420. Structural rivets have a steel body. Structural rivets have a steel mandrel.

Structural rivets have a rivet diameter of 3/16. Structural rivets have a grip range of .080 to .375. Structural rivets have a steel body. Structural rivets have a steel mandrel.

Clamp-type rivets have a rivet diameter of 3/16. Clamp-type rivets have a grip range of .050 to .250. Clamp-type rivets require a No. 5 drill size. Clamp-type rivets have an aluminum body.

Clamp-type rivets have a rivet diameter of 3/16. Clamp-type rivets have a grip range of .187 to .375. Clamp-type rivets require a No. 5 drill size. Clamp-type rivets have an aluminum body.

Clamp-type rivets have a rivet diameter of 3/16. Clamp-type rivets have a grip range of .250 to .563. Clamp-type rivets require a No. 5 drill size. Clamp-type rivets have an aluminum body.

Rivet type rivets have a rivet diameter of 3/16. Rivet type rivets have a grip range of .250 to .563. Rivet type rivets require a No. 5 drill size. Rivet type rivets have an aluminum body.

Rivet type rivets have a rivet diameter of 3/16. Rivet type rivets have a grip range of .187 to .375. Rivet type rivets require a No. 5 drill size. Rivet type rivets have an aluminum body.

Self sealing rivets have a rivet diameter of 5 mm. Self sealing rivets have a flange diameter of 9.5 mm. Self sealing rivets are used on windshield side moulding.

Self sealing rivet is specified with a rivet diameter of 4.8mm, a grip range of 1/8 to 11/32, and a flange diameter of 13.5mm. Self sealing rivet is used on the bumper and wheel housing. Self sealing rivet is specified to match OE 97987-6.

Peel rivet is specified with a rivet diameter of 1/4 (6.3mm), a grip range of 1/8 to 21/64, and a flange diameter of 3/4. Peel rivet is used on the door lock actuator. Peel rivet is specified to match OE NB08689-S417.

Self sealing rivet is specified with a rivet diameter of 5.9mm and a flange diameter of 12. Self sealing rivet is used on the hood insulator. Self sealing rivet is specified to match OE 9437643.

Closed end type rivet is specified with a rivet diameter of 4mm (5/32), a grip range of 1.6mm–6.3mm, and a flange diameter of 7.9mm. Closed end type rivet is specified to match OE 90084-26002.

Closed end blind rivet is specified with a hole size of 4mm, a grip range of 3mm–4.75mm, and a flange diameter of 8mm. Closed end blind rivet is specified to match OE 90269-04053.

Blind rivet is specified with a rivet diameter of 4mm (5/32), a grip range of 1.0mm–7.5mm, and a flange diameter of 8mm (5/16). Blind rivet is constructed with an aluminum body and mandrel. Blind rivet is specified to match OE 034212, 10131511, and N807620-S100.

Rear bumper blind rivet is specified with a rivet diameter of 4mm (5/32), a grip range of 1/8–7/32, and a flange diameter of 9mm (23/64). Rear bumper blind rivet is constructed with an aluminum body and mandrel. Rear bumper blind rivet is specified to match OE 12531204.

Closed end seal type blind rivet is specified with a rivet diameter of 3/16 (5mm), a grip range of 3mm–12mm, and a flange diameter of 8mm (5/16). Closed end seal type blind rivet is constructed with an aluminum body and a steel mandrel. Closed end seal type blind rivet is specified to match OE 003-990-94-97.

Bumper blind rivet is specified with a rivet diameter of 5/32 (4mm), a head diameter of 5/16 (8mm), a grip range of .040–.275, and a flange diameter of 10mm. Bumper blind rivet uses a leg retention style. Bumper blind rivet is specified to match OE 003-990-94-97.

Closed end rivet is specified with a rivet diameter of 1/4 (6.3mm), a grip range of 1/4–3/8, and a flange diameter of 1/2. Closed end rivet is constructed with an aluminum body and a steel mandrel.

General purpose rivet is specified with a rivet diameter of 3/16, a grip range of 5/64 to 3/8, and a flange diameter of 7/8. General purpose rivet is constructed with an aluminum rivet and mandrel.

Rivet is specified with a rivet diameter of 7/32 (5.6mm), a grip range of .062–.375, and a flange diameter of 8mm. Rivet is made of black nylon.

Nylon rivet is specified with a rivet diameter of 1/4 (6.3mm), a grip range of .190–.532, and a flange diameter of 21/32 (16.5mm). Nylon rivet is made of black nylon.

Rivet is specified with a rivet diameter range of 6mm–9mm, a grip range of 3mm, and a flange diameter of 13mm. Rivet is made of black nylon. Rivet is specified to match OE 5I-111-942-789.

Rivet is specified with a rivet diameter of 6mm, a grip range of 3mm, and a flange diameter of 13mm. Rivet is used on the front bumper. Rivet is made of black nylon. Rivet is specified to match OE 5I-111-8-400-709.

Nylon rivet is specified with a rivet diameter of 1/4 (6.3mm), a grip range of 5/32 to 15/64, and a flange diameter of 15mm. Nylon rivet is used on the fender liner. Nylon rivet is specified to match OE 1508444.

Blind rivet is specified with a rivet diameter of 4.9mm, a grip range of 3mm, and a flange diameter of 9mm. Blind rivet is made of black nylon. Blind rivet is specified to match OE 11588030.

Rivet is specified with a rivet diameter range of 4mm–6.5mm, a grip range of 2mm, and a flange diameter of 12mm. Rivet is made of black nylon. Rivet is specified to match OE 6973.A9.

Rivet is specified with a rivet diameter range of 4mm–6.5mm, a grip range of 2mm, and a flange diameter of 12mm. Rivet is made of black nylon. Rivet is specified to match OE N908-131-01.

Nylon blind rivet is specified with a hole diameter of 3/16 (4.8mm), a grip range of 1/16 to 11/64, and a head diameter of 15/32 (12mm). Nylon blind rivet is automotive OEM approved. Nylon blind rivet is specified to match OE N804189-S and 20423647.

Nylon blind rivet is specified with a hole diameter of 3/16 (4.8mm), a grip range of 1/8 to 15/64, and a head diameter of 15/32 (12mm). Nylon blind rivet is automotive OEM approved. Nylon blind rivet is specified to match OE 6500899, 175-853-577, and 20432975.

Nylon blind rivet is specified with a hole diameter of 3/16 (4.8mm), a grip range of 3mm, and a head diameter of 15/32 (12mm). Nylon blind rivet is automotive OEM approved. Nylon blind rivet is specified to match OE 6500859.

Nylon blind rivet is specified with a hole diameter of 3/16 (4.8mm), a grip range of 3mm, and a head diameter of 15/32 (12mm). Nylon blind rivet is automotive OEM approved. Nylon blind rivet is specified to match OE 10035603.

Nylon blind rivet is specified with a hole diameter of 3/16 (4.8mm), a grip range of 1.5mm, and a head diameter of 15/32 (12mm). Nylon blind rivet is automotive OEM approved. Nylon blind rivet is specified to match OE 8064212 and 20465395.

Nylon blind rivet is specified with a hole diameter of 3/16 (4.8mm), a grip range of 1.5mm, and a head diameter of 15/32 (12mm). Nylon blind rivet is automotive OEM approved. Nylon blind rivet is specified to match OE 20612732.

Nylon blind rivet is specified with a hole diameter of 3/16 (4.8mm), a grip range of 1.5mm, and a head diameter of 15/32 (12mm). Nylon blind rivet is automotive OEM approved. Nylon blind rivet is specified to match OE N805132-S.

Nylon blind rivet is specified with a hole diameter of 3/16 (4.8mm), a grip range of 1.5mm, and a head diameter of 15/32 (12mm). Nylon blind rivet is automotive OEM approved. Nylon blind rivet is specified to match OE 25524005.

Nylon blind rivets have a hole diameter of 1/4 (6.3mm), a grip range of 3mm, and a head diameter of 25/32 (20mm). Nylon blind rivets are automotive OEM approved and reference OE N806296-S for technical fitment identification.

Nylon blind rivets have a hole diameter of 1/4 (6.3mm), a grip range of 4mm, and a head diameter of 25/32 (20mm). Nylon blind rivets are automotive OEM approved and reference OE 15568272 for technical fitment identification.

Nylon blind rivets have a hole diameter of 1/4 (6.3mm), a grip range of 4mm, and a head diameter of 25/32 (20mm). Nylon blind rivets are automotive OEM approved and reference OE 10109689 and 12337915 for technical fitment identification.

Nylon blind rivets have a hole diameter of 9/32 (7mm), a grip range of 2.5mm, and a head diameter of 25/32 (20mm). Nylon blind rivets are automotive OEM approved and reference OE 10109689 and 12337915 for technical fitment identification.

Nylon blind rivets have a hole diameter of 1/4 (6.3mm), a grip range of 4mm, and a head diameter of 25/32 (20mm). Nylon blind rivets are automotive OEM approved and reference OE 20433026 and 175-853-577A for technical fitment identification.

Nylon blind rivets have a hole diameter of 1/4 (6.3mm), a grip range of 3mm, and a head diameter of 25/32 (20mm). Nylon blind rivets are automotive OEM approved and reference OE 15595172 and 20421672 for technical fitment identification.

Nylon blind rivets have a hole diameter of 1/4 (6.3mm), a grip range of 3mm, and a head diameter of 25/32 (20mm). Nylon blind rivets are automotive OEM approved and reference OE 20433026 and 175-853-577A for technical fitment identification.

Special rivets have a rivet diameter of 1/8, a grip range of 1/16 to 3/16, a drill size of #30, and an aluminum body.

Special rivets have a rivet diameter of 1/8, a grip range of 1/8 to 1/4, a drill size of #29, and an aluminum body.

Special rivets have a rivet diameter of 1/8, a grip range of 3/16 to 3/16, a drill size of #18, and an aluminum body.

Special rivets have a rivet diameter of 1/4, a grip range of 1/16 to 11/64, a flange diameter of 7/16, and an aluminum body. Special rivets reference OE 20713843 for technical fitment identification.

Special rivets have a rivet diameter of 1/4, a grip range of 9/64 to 3/16, a flange diameter of 7/8, and an aluminum body. Special rivets reference OE 6032296 and 9437486 for technical fitment identification.

Special rivets have a rivet diameter of 1/4, a grip range of 13/32 to 1/8, a flange diameter of 1, and an aluminum body. Special rivets reference OE 388047-S102 for technical fitment identification.

Special rivets have a rivet diameter of 3/16, a grip range of 1/8 to 5/8, a flange diameter of 5/8, and an aluminum body. Special rivets reference OE 2085119, 3533539, and 3540161 for technical fitment identification.

Special rivets have a rivet diameter of 3/16, a grip range of 1/4 to 3/8, a flange diameter of 3/8, and a steel body. Special rivets reference OE 9437919 for technical fitment identification.

Special rivets have a rivet diameter of 3/16, a grip range of 5/64 to 15/64, a flange diameter of 5/16, and an aluminum body. Special rivets reference OE N805592-S100 and 2561873 for technical fitment identification.

Special rivets have a rivet diameter of 3/16, a grip range of 5/64 to 15/64, a flange diameter of 5/16, and an aluminum body. Special rivets reference OE 10125439 for technical fitment identification.

Special rivets have a rivet diameter of 1/8, a grip range of 1/8 to 3/16, a flange diameter of 3/8, and an aluminum body. Special rivets reference OE 9432552 for technical fitment identification.

Special rivets have a rivet diameter of 1/8, a grip range of 3/8, a flange diameter of 3/8, and an aluminum body. Special rivets reference OE 9432552 for technical fitment identification.

Special rivets have a rivet diameter of 3/16, a grip range of 1/8 to 3/16, a flange diameter of 3/8, and an aluminum body. Special rivets reference OE 9439576 for technical fitment identification.

Special rivets have a rivet diameter of 3/16, a grip range of 1/8 to 3/16, a flange diameter of 3/8, and an aluminum body. Special rivets reference OE 9440392 for technical fitment identification.

Special rivets have a rivet diameter of 1/8, a grip range of 1/8 to 3/16, a flange diameter of 3/8, and an aluminum body. Special rivets reference OE 2032569 for technical fitment identification.

Special rivets have a rivet diameter of 1/8, a grip range of 3/8, a flange diameter of 3/8, and an aluminum body. Special rivets reference OE N805759-S100 for technical fitment identification.

Special rivets have a rivet diameter of 1/8, a grip range of 3/16, a drill size of #8, and a stainless steel body.

Special rivets have a rivet diameter of 1/4, a grip range of 1/8 to 9/16, a flange diameter of 1/2, and an aluminum body. Special rivets reference OE 6031115, 00405791, 385189-S100, and 9436175 for technical fitment identification.

Special rivets have a rivet diameter of 1/4 (6.3mm), a grip range of 1/4 to 3/4, and a flange diameter of 11/64. Special rivets are specified for windshield regular, glass applications and reference OE 389258-S100 and 12383153 for technical fitment identification.

Special rivet fastener has a rivet diameter of 1/4 (6.3mm), a grip range of 3/32 to 1/8, and a flange diameter of 3/8. Special rivet fastener is specified for windshield regular, glass applications.

Special rivet fastener has a rivet diameter of 1/4 (6.3mm), a grip range of 3/8, and a flange diameter of 1/4. Special rivet fastener has a steel body.

Special rivet fastener has a rivet diameter of 1/4 (6.3mm), a grip range of 3/8, and a flange diameter of 1/4. Special rivet fastener has a steel body.

Special rivet fastener has a rivet diameter of 3/16, a grip range of 3/16 to 1/2, and a flange diameter of 3/8. Special rivet fastener is specified for fascia and bumper applications.

Special rivet fastener has a rivet diameter of 1/8, a grip range of 3/32 to 3/16, and a flange diameter of 1/2. Special rivet fastener is a black aluminum rivet with a steel mandrel.

Specialty rivet fastener has a rivet diameter of 3/16 (4.8mm), a grip range of 3/16 to 3/8, and a flange diameter of 5/16. Specialty rivet fastener is specified for bumper cover split type applications.

Specialty rivet fastener has a rivet diameter of 1/4 (6.3mm), a grip range of 3/8 to 3/4, and a flange diameter of 3/8. Specialty rivet fastener attaches the power lock motor or sole.

Specialty rivet fastener has a rivet diameter of 5/32 (4mm), a grip range of 3/64 to 3/8, and a flange diameter of 3/4. Specialty rivet fastener is a black aluminum rivet with a steel mandrel.

Specialty rivet fastener has a rivet diameter of 5/32 (4mm), a grip range of 3/64 to 3/8, and a flange diameter of 3/4. Specialty rivet fastener is a black aluminum rivet with a steel mandrel.

Rivet fastener has a rivet diameter of 3/16, a grip range of 3/16 to 7/16, and a flange diameter of 3/8. Rivet fastener is specified for door handle applications.

Blind peel type rivet fastener has a rivet diameter of 1/4 (6.3mm), a grip range of .126-.326, and a flange diameter of 7/16. Blind peel type rivet fastener is specified for door window regular applications.

Belt moulding blind rivet fastener has a rivet diameter of 3.2mm (0.126), a grip range of 3.2mm-4.75mm, and a flange diameter of 5.5mm.

Bumper blind rivet fastener has a rivet diameter of 1/4 (6.3mm), a grip range of 3/16 to 3/8, and a flange diameter of 5/8 (15.9mm). Bumper blind rivet fastener has a steel body and a steel mandrel.

All steel specialty rivet fastener has a rivet diameter of 1/4 (6.3mm), a grip range of 1/16 to 3/16, and a flange diameter of 1/2 (13mm). All steel specialty rivet fastener is a galvanized rivet with a steel mandrel.

Rivet fastener has a rivet diameter of 4.8mm (3/16), a grip range of 3mm, and a flange diameter of 9mm. Rivet fastener is a steel rivet with a steel mandrel.

Blind rivet fastener has a rivet diameter of 1/2 and a grip range of 5/8 to 3/4. Blind rivet fastener is a steel rivet with a steel mandrel.

Blind rivet fastener has a rivet diameter of 1/4, a grip range of 3/16 to 3/8, and a flange diameter of 1/16. Blind rivet fastener is specified for license plate applications.

Split-type rivet fastener has a rivet diameter of 4.8mm (3/16), a grip range of 3/64 to 15/64, and a flange diameter of 3/8. Split-type rivet fastener is a black aluminum rivet with an aluminum mandrel.

Split-type rivet fastener has a diameter of 3/16, a grip range of 3/64 to 15/64, and a flange diameter of 3/8. Split-type rivet fastener is aluminum.

Bumper rivet fastener is specified with special notes stating that the recommended size is given first, followed by an acceptable alternate size. Bumper rivet fastener requires a special nosepiece.

Bumper rivet fastener has a rivet diameter of 3/16, a head diameter of 5/8, a rivet length of 9/16, and a grip range of 1/4. Bumper rivet fastener uses a drill size of No. 12 and is steel. 

Bumper rivet fastener is specified for fascia to underside of bumper applications, installed blind, with a zinc mandrel and a black body.

Bumper rivet fastener has a rivet diameter of 1/4, a head diameter of 1/2, a rivet length of 1/2, and a grip range of 3/8. Bumper rivet fastener uses a drill size of F or 1/4 and is steel. Bumper rivet fastener is specified for front bumper assembly applications on Bobcat, Pinto, and Van.

Bumper rivet fastener has a rivet diameter of 1/4, a head diameter of 3/4, a rivet length of 1/2, and a grip range of 3/8. Bumper rivet fastener uses a drill size of F or 1/4 and is steel. Bumper rivet fastener is specified for rear bumper assembly applications with a zinc coated mandrel and a black body.

Bumper rivet fastener has a rivet diameter of 3/16, a head diameter of 9/16, a rivet length of 11/16, and a grip range of 3/8. Bumper rivet fastener uses a drill size of No. 12 and is aluminum. Bumper rivet fastener is specified for front bumper applications with a black body.

Bumper rivet fastener has a rivet diameter of 1/4, a head diameter of 9/16, a rivet length of 15/16, and a grip range of 1/4. Bumper rivet fastener uses a drill size of 1/4 and is aluminum. Bumper rivet fastener is specified for Ford Taurus applications, installed blind, with a style leg retention style.

Special application rivet specifications include a rivet diameter of 3/16, a head diameter of 7/16, a rivet length of 13/16, a grip range of 5/64, and a drill size of No. 12, and the material is aluminum. Special application rivet OE manufacturer is Ford. Special application rivet application is Lincoln wheel house mounting for the 1989 model with leg retention style.

Special application rivet specifications include a rivet diameter of 3/16, a head diameter of 3/8, a rivet length of 13/16, a grip range of 5/64, and a drill size of No. 12, and the material is aluminum. Special application rivet OE manufacturer is GM. Special application rivet application is Lincoln wheel house mounting for 1994-1995 models with black body.

Special application rivet specifications include a rivet diameter of 1/8, a head diameter of 3/8, a rivet length of 3/8, a grip range of 1/8, and a drill size of No. 30, and the material is aluminum. Special application rivet OE manufacturer is GM. Special application rivet application is GM floor press.

Special application rivet specifications include a rivet diameter of 3/16, a head diameter of 3/8, a rivet length of 3/8, a grip range of 1/8, and a drill size of No. 12, and the material is steel. Special application rivet OE manufacturer is GM. Special application rivet application is GM roof.

Special application rivet specifications include a rivet diameter of 3/16, a head diameter of 3/8, a rivet length of 1/2, a grip range of 1/8, and a drill size of No. 12, and the material is steel. Special application rivet OE manufacturer is GM. Special application rivet application is GM roof.

Special application rivet specifications include a rivet diameter of 1/8, a head diameter of 5/16, a rivet length of 5/16, a grip range of 3/16, and a drill size of No. 30, and the material is aluminum. Special application rivet OE manufacturer is GM. Special application rivet application is in-roof window on “X” body, 81-on.

Special application rivet specifications include a rivet diameter of 3/16, a head diameter of 5/16, a rivet length of 5/16, a grip range of 3/16, and a drill size of No. 12, and the material is aluminum. Special application rivet OE manufacturer is Ford. Special application rivet application is windshield glass with black finish.

Special application rivet specifications include a rivet diameter of 5/32, a head diameter of 5/16, a rivet length of 5/16, a grip range of 3/16, and a drill size of No. 22, and the material is aluminum. Special application rivet OE manufacturer is Chevy. Special application rivet application is front lock swivel, emblem rivet, 73-on.

Nylon blind rivet specifications include a hole diameter of .396, an “A” panel range of 6.0 to 10.5, a “B” head diameter of 8.0 x 15.0, a “C” stem diameter of 9.0, and a black color. Nylon blind rivet OE manufacturer is Ford.

Nylon blind rivet specifications include a hole diameter of .375, an “A” panel range of 1.5 to 4.5, a “B” head diameter of 9.0, a “C” stem diameter of 9.0, and a black color. Nylon blind rivet OE manufacturer is Ford.

Nylon blind rivet specifications include a hole diameter of .376, an “A” panel range of 1.6 to 4.5, a “B” head diameter of 11.5, a “C” stem diameter of 9.0, and a black color. Nylon blind rivet OE manufacturer is Ford.

Nylon blind rivet specifications include a hole diameter of .316, an “A” panel range of 1.5 to 6.0, a “B” head diameter of 9.0, a “C” stem diameter of 8.0, and a black color. Nylon blind rivet OE manufacturers are Ford and GM.

Nylon blind rivet specifications include a hole diameter of .350, an “A” panel range of 1.6 to 4.5, a “B” head diameter of 12.0, a “C” stem diameter of 15.0, and a black color. Nylon blind rivet OE manufacturers are GM and Chevy.

Nylon blind rivet specifications include a hole diameter of .364, an “A” panel range of 3.0 to 6.0, a “B” head diameter of 15.0, a “C” stem diameter of 15.0, and a black color. Nylon blind rivet OE manufacturer is GM.

Nylon blind rivet specifications include a hole diameter of .350, an “A” panel range of 1.5 to 4.5, a “B” head diameter of 12.0, a “C” stem diameter of 15.0, and a black color. Nylon blind rivet OE manufacturers are GM and Chevy.

Nylon blind rivet specifications include a hole diameter of .364, an “A” panel range of 3.0 to 6.0, a “B” head diameter of 15.0, a “C” stem diameter of 15.0, and a black color. Nylon blind rivet OE manufacturer is GM.

Nylon blind rivet specifications include a hole diameter of .364, an “A” panel range of 3.0 to 6.0, a “B” head diameter of 15.0, a “C” stem diameter of 15.0, and a black color. Nylon blind rivet OE manufacturer is GM.

Nylon blind rivet specifications include a hole diameter of .364, an “A” panel range of 3.0 to 6.0, a “B” head diameter of 15.0, a “C” stem diameter of 15.0, and a black color. Nylon blind rivet OE manufacturer is GM.

Nylon blind rivets are specified with a hole diameter of .564, an “A” panel range of 4.6 to 8.0, a “B” head diameter of 12.0, a “C” stem diameter of 16.5, and a black color. OE fitment is listed as GM 25524005.

Nylon blind rivets are specified with a hole diameter of .630, an “A” panel range of 3.0 to 6.0, a “B” head diameter of 21.5, a “C” stem diameter of 21.5, and a black color. OE fitment is listed as Ford N804134-S.

Nylon blind rivets are specified with a hole diameter of .630, an “A” panel range of 4.0 to 10.5, a “B” head diameter of 21.5, a “C” stem diameter of 21.5, and a black color. OE fitment is listed as Ford N806296-S.

Nylon blind rivets are specified with a hole diameter of .630, an “A” panel range of 4.0 to 10.5, a “B” head diameter of 21.5, a “C” stem diameter of 21.5, and a black color. OE fitment is listed as Ford N806296-S.

Nylon blind rivets are specified with a hole diameter of .630, an “A” panel range of 5.0 to 10.5, a “B” head diameter of 21.5, a “C” stem diameter of 21.5, and a black color. OE fitment is listed as GM 6500859.

Nylon blind rivets are specified with a hole diameter of .630, an “A” panel range of 7.5 to 13.0, a “B” head diameter of 21.5, a “C” stem diameter of 21.5, and a black color. OE fitment is listed as GM 10035603.

Nylon blind rivets are specified with a hole diameter of .784, an “A” panel range of 3.2 to 6.0, a “B” head diameter of 15.0, a “C” stem diameter of 18.0, and a black color. OE fitment is listed as Ford N806296-S.

Nylon blind rivets are specified with a hole diameter of .784, an “A” panel range of 5.0 to 10.5, a “B” head diameter of 18.0, a “C” stem diameter of 23.5, and a black color. OE fitment is listed as GM 10109689 and GM 12337915.

A heavy duty riveter sets 1/4 inch and 3/16 inch stainless steel rivets and sets all special body shop rivets. A heavy duty riveter stores extra nosepieces in holes on the tool body. A heavy duty riveter features steel threads and a lightweight aluminum body. 

A heavy duty riveter sets 1/8 inch through 1/4 inch rivets, including special door, window regulator, and glass stop rivets. A heavy duty riveter uses long handles and a gear reduction system to set even 1/4 inch stainless rivets. 

A heavy duty riveter includes 5/32 inch, 3/16 inch, and 1/4 inch rivet nosepieces. A heavy duty riveter uses optional nosepieces for special body rivets and monobolts as specified by the chart.

Combined drill and countersink bits are double-ended to provide double the wear and double the life. Combined drill and countersink bits have drill ends of equal diameter. Combined drill and countersink bits have a 135 degree point.

A double-end straight shank drill bit has a 135 degree self-centering split point. A double-end straight shank drill bit has an extra sharp point always hand. A double-end straight shank drill bit fits a drill chuck without damage. A double-end straight shank drill bit has a stubby length that reduces breakage. A double-end straight shank drill bit is ideal for drilling sheet metal 1/4 inch thick or less.

An industrial rivet gun is specified as the most advanced industrial hand riveter. An industrial rivet gun contains four nosepieces for 3/32 inch, 1/8 inch, 5/32 inch, and 3/16 inch diameter rivets.

Special mandrels (nosepieces) are required to install certain trim, door, window regulator, and glass stop rivets and monobolt structural rivets.

Special rivet type trim rivets include Snap-Head 4/8 inch (400T), monobolt, Klimp-Tite rivet, and split rivets. Special rivet type trim rivets include 3/16 inch monobolt. Special rivet type trim rivets include 1/4 inch monobolt. Special rivet type trim rivets include a 3/16 inch Klimp-Tite rivet. Special rivet type trim rivets include a 1/4 inch rivet. Special rivet type trim rivets include a 3/16 inch rivet.

____________________________________________________________________________

Screws 

Truck mirror mounting screws use 1/4-20 × 1 inch fasteners with a washer head measuring 5/8 inch and a hex size of 3/8 inch for outside mirror attachment, with OE references including 367291, 474821, and 14007511, specifications commonly encountered during truck mirror service and replacement work in body shops serving Hoosick Falls, New York.

Sheet metal screws include No. 14 x 3/4 slotted hex washer head fasteners. 

Sheet metal screws include No. 6 x 3/4 Phillips oval head fasteners with a black oxide finish. 

Sheet metal screws include No. 8 x 3/4 Phillips oval head fasteners with a black oxide finish. 

Sheet metal screws include No. 6 x 1 Phillips oval head fasteners with a black oxide finish. 

Sheet metal screws include No. 6 x 1-1/4 Phillips oval head fasteners with a black oxide finish. 

Sheet metal screws include No. 8 x 1 Phillips oval head fasteners with a black oxide finish. 

Sheet metal screws include No. 8 x 1-1/4 Phillips oval head fasteners with a black oxide finish. 

Sheet metal screws include No. 8 x 1-1/2 Phillips oval head fasteners with a black oxide finish. 

Sheet metal screws include No. 8 x 1-1/4 Phillips oval head fasteners with a black oxide finish. 

Sheet metal screws include No. 10 x 1 Phillips oval head fasteners with a black oxide finish. 

Sheet metal screws include No. 10 x 1-1/4 Phillips oval head fasteners with a black oxide finish. 

Sheet metal screws include No. 10 x 1-1/2 Phillips oval head fasteners with a black oxide finish. 

Sheet metal screws include No. 10 x 1-1/2 Phillips oval head fasteners with a black oxide finish. 

Sheet metal screws include No. 10 x 1-1/2 Phillips oval head fasteners with a black oxide finish. 

Sheet metal screws include No. 10 x 1-1/2 Phillips oval head fasteners with a black oxide finish. 

Sheet metal screws include No. 10 x 2 Phillips oval head fasteners with a black oxide finish.

Sheet metal self-tapping screws use 8-18 x 5/8 fasteners with an indented hex head and a Phillips drive with a large round washer.

Sheet metal screws include 4.2 mm x 21 mm fasteners listed as No. 8 x 5/8, with a washer outside diameter of 16 mm (5/8), and a Phillips pan head. Sem tap screws include OE reference N806103-S2.

Weld stud replacement screws use No. 4-24 x 3/8 fasteners with a head diameter of 7/32 and a Phillips head in stainless steel.

Phillips truss head tapping screws use M4.8-1.0 x 15 mm (5/8) fasteners with a head outside diameter of 14 mm (9/16) and a black phosphate finish. OE references include 91501-00841 and 12439-51678.

Bumpers use bumper fascia screws with a head size of 22 mm and a 9.5 mm x 40 mm square drive configuration in black nylon. OE reference includes 2505182.

Indented hex head screws include 4.8 mm-1.61 x 16 mm fasteners with a 15 mm washer, an 8 mm across flats dimension, and a Type AB point with a sems washer. Indented hex head screws include 4.8 mm-1.61 x 15 mm fasteners with an 8 mm across flats dimension and a Type AB point with a sems washer.

License plate screws use 1/4 x 5/8 slotted truss head fasteners. License plate screws with nuts use a No. 14 nut with a .28 square hole and a 9/32 flange, paired with a No. 14 x 3/4 screw. License plate screws with nuts use a No. 14 nut with a .28 square hole and a 5/8 flange, paired with a No. 14 x 3/4 screw.

License plate screws use 1/4 x 5/8 combo Phillips/slotted pan head fasteners with a Type B point. OE reference includes 9423101.

Indented hex head screws include 4.8 mm-1.61 x 15 mm fasteners with an 8 mm across flats dimension and a Type AB point with a sems washer.

License plate machine screws use 1/4-20 x 3/4 fasteners with a Phillips truss head. License plate metal screws use No. 14 x 3/4 slotted hex washer head fasteners with a zinc finish.

License plate screws with nuts use No. 10 x 5/8 fasteners with a 1/4 square hole and a slotted washer head in nylon. OE reference includes 3780006.

License plate screws use No. 14 x 3/4 Phillips truss head fasteners.

License plate bolts use an indented hex head configuration with a 19 mm washer and a loose washer. OE reference includes N806766-S58.

License plate screws use 6 mm x 20 mm fasteners with a Phillips washer head.

License plate screws with nylon slotted washer head use 1/4 x 5/8 fasteners with nylon nuts.

License plate screws with nuts use 6 mm-1.0 x 20 mm fasteners with a head diameter of 10 mm (25/64) and a Phillips pan head.

Machine screws use 6 mm-1.0 x 25 mm slotted pan head fasteners built to DIN 85 with a zinc plated finish.

Interior trim screws use 6.3 mm-1.81 x 16 mm fasteners with a 15 mm (19/32) head and a Phillips truss head, and they have a black phosphate finish.

Sems tapping screws use 4.8 mm-1.61 x 20 mm fasteners with an 8 mm hex head and a washer outside diameter of 26 mm for front bumper moulding strip attachment. OE reference includes 20000-05-36.

License plate screws use No. 14 x 5/8 fasteners with a 5/16 hex size, a washer head outside diameter of 5/8, and a slotted hex washer head. OE reference includes N800369.

License plate screws use No. 14 x 5/8 fasteners with a 5/16 hex size, a washer head outside diameter of 5/8, and a slotted hex washer head. OE reference includes N800369-S2.

License plate screws use 6 mm x 16 mm fasteners with a 12 mm flange, a 10 mm across flats dimension, and an indented hex Phillips washer head. OE references include 9390-46320 and 91500-SM4-999AH.

License plate screws use 6 mm x 20 mm fasteners with a 12 mm flange, a 10 mm across flats dimension, and an indented hex Phillips washer head. OE reference includes 91500-SM4-999AH.

Square drive truss head fascia screws use 7.5 mm x 34.2 mm fasteners with a 22 mm head diameter and a 9 mm shoulder diameter, and they attach foam to bumper. Square drive truss head fascia screws are made of black nylon. OE references include 6503401, 6503819, and 25631448.

Tapping screws use 4.8 mm-1.41 x 20 mm fasteners with a 7 mm across flats dimension and an indented hex head, and they include a Type AB point. OE reference includes 14090382.

Tapping screws use 4.8 mm-1.41 x 20 mm fasteners with a 7 mm across flats dimension and an indented hex head, and they include a Type AB point.

Tapping screws use 4.2 mm-1.41 x 15 mm fasteners with a 12 mm washer and a Phillips pan head, and they include a Type B point. OE reference includes 11503499.

Tapping screws use 6.3 mm-1.81 x 23 mm fasteners with a 10 mm across flats dimension, 17 mm SEMS, and an indented hex head, and they include a Type AB point. OE references include 11500996 and 11505023.

Tapping screws use 6.3 mm-1.81 x 23 mm fasteners with a 10 mm across flats dimension, 17 mm SEMS, and an indented hex head, and they include a Type AB point. OE reference includes 11505022.

Tapping screws use No. 10 x 3/4 fasteners with an indented hex size of 13/32 and a 5/16 across flats dimension.

Tapping screws use 4.2 mm-1.41 x 25 mm fasteners with a washer head outside diameter of 11 mm (7/16) and a Phillips washer head, and they have a black oxide finish. OE reference includes 11501884.

Tapping screws use 5.5 mm x 20 mm fasteners with a head size of 15 mm (19/32) and a Torx truss head T-20, and they have a black zinc finish. OE reference includes 13144822.

Tapping screws use 6 mm-1.8 x 20 mm fasteners with a 13 mm washer outside diameter, a 10 mm hex size, and a Phillips head SEMS configuration for bumper exterior trim applications. OE reference includes MS452438.

Tapping screws use 5 mm-1.59 x 11 mm fasteners with an 11 mm head size and a Phillips truss head for interior trim applications. OE reference includes MF453091.

Tapping screws use No. 14 x 3/4 fasteners with a head outside diameter of 15/32, and they are made of stainless steel with a Phillips pan head.

Tapping screws use 5 mm-1.59 x 11 mm fasteners with a washer head outside diameter of 12 mm and a Phillips round washer head, and they have a black oxide finish.

Sheet metal tapping screws use 4.2 mm-1.41 x 20 mm fasteners with an attached 16 mm washer and an indented hex head, and they are configured with an attached washer in black. OE references include 11502449 and 1640810.

Sheet metal tapping screws use 4.2 mm-1.41 x 20 mm fasteners with an attached 12 mm washer, a 7 mm hex size, and an indented hex head, and they are configured with an attached washer. OE references include 11500434, 11503892, and 1640810.

Sheet metal tapping screws use 4.8 mm-1.61 x 19 mm fasteners with a 16 mm washer outside diameter and a Phillips truss head SEMS configuration, and they have a black E-coat finish. OE reference includes 90114-SE0-000.

Thumb screws use No. 14 x 1/2 fasteners with an overall length of 1-1/8 for dealer license plate use.

Trim screws use 8-18 x 1/2 fasteners with a 5/16 washer outside diameter and a Phillips washer head for outer wheel house moulding applications. OE reference includes 588546.

Trim screws use 8-18 x 1/2 fasteners with a Phillips flat head and sealer. OE reference includes 9428196.

Reveal moulding to panel fasteners use 8-18 x 1/2 Phillips truss head screws with a Teks point for wheel house moulding applications, and they have a zinc finish. OE reference includes 1689827.

Trim screws use 8 x 5/8 fasteners with a Phillips oval head and a bright zinc finish.

Trim screws use 8 x 3/8 fasteners with an oval head. OE reference includes 9431911.

Trim screws use 8-18 x 1/2 fasteners with a head diameter of 7/16 and a Phillips round washer head. OE reference includes 4065091.

____________________________________________________________________________

Trim Screws 

Trim screws include stainless steel weld stud replacement screws with a Phillips drive slot. 

Stainless steel weld stud replacement screws use a Phillips slot that reduces distortion and screwdriver slippage. Stainless steel weld stud replacement screws use a universal shoulder length that accepts all weld stud clips. 

Stainless steel weld stud replacement screws use a short thread length that reduces installation time and eliminates interference in clip applications. Stainless steel weld stud replacement screws are used on vehicles that can have as many as 150 weld studs per car. 

Stainless steel weld stud replacement screws are specified to eliminate stripping and loose retainers and are used where weld studs are broken due to collision damage or during repair, conditions commonly addressed in structural and panel repair work performed by body shops in and around Catskill, New York.

Stainless steel weld stud replacement screws stop and lock at the shoulder. Stainless steel weld stud replacement screws use an extra sharp point to start easily and self-align.

Phillips oval head tapping screws with a Type AB point are provided with an undersized head configuration.

Phillips oval head tapping screws with a Type AB point are provided with a standard head configuration.

Phillips oval head tapping screws with a Type AB point are provided with a 3/8 inch diameter round washer head.

Phillips round head tapping screws with a Type AB point are provided with a 1/2 inch diameter round washer head.

Phillips oval head tapping screws with a Type AB point and flushwasher are provided in a Type AB SEMS configuration with a reduced head.

Phillips oval head trim screws with a Type AB point and countersunk washer are provided for trim attachment where a countersunk washer configuration is required.

Black oxide trim screws are used on instrument panels and interior trim.

Extra long trim screws use a Phillips oval head. Extra long trim screws are intended for universal applications. Extra long trim screws are used on headlamps, parking lights, and grilles.

Drill point moulding and trim screws are provided with a round washer head for wheel housing moulding with T8Wax sealer.

Metric round washer head fasteners are provided in a metric round washer head configuration.

Indented hex head screws are provided in an indented hex head configuration.

____________________________________________________________________________

Washers 

Oversize washers are designed for applications requiring a large bearing surface. Oversize washers are specified for universal applications.

Metric fender washers are manufactured to DIN 9021. Metric fender washers have an oversized outside diameter approximately 3 times the bolt diameter. 

Metric fender washers are Class 8.8. Metric fender washers are used for applications that require a large bearing surface. Metric fender washers are yellow zinc plated.

Nickel plated finishing washers are made of brass with a nickel plated finish to prevent corrosion and are used on headliners, door panels, and similar interior trim applications, as commonly encountered in body shop interior repair and restoration work in and around Latham, New York.

____________________________________________________________________________

Miscellaneous 

Cable ties are made of black nylon with an overall length of 5 mm (3/16), a strap width of 3 mm (1/8), and a maximum bundle diameter of 47 mm (1-5/16).

Cable ties are made of black nylon with an overall length of 7 mm (3/16), a strap width of 5 mm (3/16), and a maximum bundle diameter of 36 mm.

Cowl panel vent caps are made of black nylon with a top head diameter of 16 mm x 18 mm, a bottom head diameter of 14 mm, and a stem length of 12 mm.

Door roller pin assemblies have a diameter of 5-1/2, a roller outside diameter of 3/4, and a roller groove diameter of 5/8.

Door roller pins have a length of 5-1/2, a diameter of 5/8, a roller outside diameter of 3/4, and a roller groove diameter of 5/8.

Garnish moulding fasteners measure 1/2 × 1/2 × 5/8 and are used for nut plate retaining trim and screw door opening trim applications, with a zinc and yellow finish, specifications commonly encountered during interior and exterior trim service work performed by body shops in and around Ballston Spa, New York.

Fasteners have an overall length of 15/16 and are used on door interior trim and the instrument panel.

Hog ring pliers have a straight nose spring grip.

Hog rings are medium with a gauge of 14, an opening of .380, and a wire diameter of .080.

Hog rings are large with a gauge of 13, an opening of .780, and a wire diameter of .080.

Hole plugs fit 25 mm openings, have a diameter of 28 mm, and are made of black nylon.

Snap-in sheet metal plugs fit a 3/8 hole, have a head diameter of 3/4, fit material from 14 to 26 gauge, and are made of black polyethylene.

Snap-in sheet metal plugs fit a 1/2 hole, have a head diameter of 7/8, fit material from 14 to 26 gauge, and are made of black polyethylene.

Snap-in sheet metal plugs fit a 3/4 hole, have a head diameter of 1-5/32, fit material from 14 to 26 gauge, and are made of black polyethylene.

Snap-in sheet metal plugs fit a 7/8 hole, have a head diameter of 1-7/16, fit material from 14 to 26 gauge, and are made of black polyethylene.

Snap-in sheet metal plugs fit a 1 hole, have a head diameter of 1-3/4, fit material from 14 to 26 gauge, and are made of black polyethylene.

Push pin removal pliers are provided as a 2-piece set consisting of straight pliers and 75 degree offset pliers.

Body alignment shims have a thickness of 1/8, dimensions of 1-3/4 x 1-1/4, a slot of 1/2, and a zinc finish.

Body alignment shims have a thickness of 1/16, dimensions of 1-1/4 x 5/8, a slot of 3/8, and a zinc finish.

Body alignment shims have a thickness of 1/8, dimensions of 1-1/4 x 5/8, a slot of 3/8, and a zinc finish.

Body alignment shims have a thickness of 1/8, dimensions of 1-7/8 x 1-3/4, a slot of 3/8, and a zinc finish.

Body alignment shims have a thickness of 1/8, dimensions of 2 x 1-1/2, a slot of 3/4, and a zinc finish.

Body alignment shims have a thickness of 1/16, an outside diameter of 1-5/16, a slot of 3/8, and a zinc finish.

Body alignment shims have a thickness of 1/8, an outside diameter of 1-5/16, a slot of 3/8, and a zinc finish.

Cable straps are made of black nylon with a width of 8 mm (5/16), an overall length of 200 mm (8 inches), and a maximum bundle diameter of 55 mm (2-3/16).

Cable straps are made of black nylon with a width of 7 mm (9/32), an overall length of 170 mm (6-3/4), and a maximum bundle diameter of 40 mm (1-9/16).

Front door window guides are specified for front door applications.

Window guides are specified for front door applications.

Window regulator guides are made of white nylon.

Windshield garnish interior trim panel components include bezels and soft plate clips.